TVS TVS XL 100 Manual Download Page 33 | Manualshive

Page: 33 / 44

background image

BRAKES

Front brake

1. Measure the free play of the front brake lever at

the lever end as shown in the figure.

2. The free play of the brake lever before the

engagement of the brake should be between
15 ~ 20 mm.

3. If the measured free play is more or less than

the specified limit, adjust the nut provided at
the front wheel end to obtain the correct play.

4. Turn the adjuster nut in clockwise direction for

reducing the free play or turn it in anticlockwise
direction for increasing the free play.

Rear brake

1. Measure the free play of the rear brake lever at

the lever end as shown in the figure.

2. The free play of the brake lever before the

engagement of the brake should be between
15 ~ 20 mm.

MAINTENANCE

A

B

-29-

Warning

Brakes are items of personal safety and should
always be maintained in proper condition.

MAINTENANCE

«
...
31
32
33
34
35
...
»

Summary of Contents for TVS XL 100













































Reviews:

No comments

Related manuals for TVS XL 100

Brand: Honda Pages: 25

RACE 13100CP520

Brand: Yoshimura Pages: 7

Brand: AFX Pages: 52

KTM390-14-01-SL

Brand: SRC Pages: 4

Brand: R&G Pages: 27

Brand: Zero Pages: 290

Brand: Yamaha Pages: 287

Brand: Yamaha Pages: 109

Brand: Surtek Pages: 12

Brand: Arai Pages: 15

Brand: Sealey Pages: 2

Brand: Wunderlich Pages: 4

Brand: Wunderlich Pages: 3

Brand: Wunderlich Pages: 7

Brand: Wunderlich Pages: 9

Brand: Aosom Pages: 13

Brand: Bike Shield Pages: 4

Brand: RIEJU Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands