background image

l

Basic:

Demineralized water is supplied by a manually filled reservoir,

demineralized water overflow outlet on the rear cover:
(device catalog number: AMS11-120-T -

T-Edge 11

)

l

Automatic:

Demineralized water direct inlet from the water supply

system, demineralized water overflow, and waste water outlet on the
rear cover:
(device catalog number: AMS11-120-W-T -

T-Edge 11-W

)

1.5 Intended Use

The T-Edge 11 tabletop autoclave is designed for sterilization of medical and
surgical goods such as wrapped and unwrapped solid, hollow, and porous
loads used in dental and medical clinics, first aid rooms, hospitals, and
laboratories etc.

1.6 Intended Users

The T-Edge 11 tabletop autoclave is intended for use by hospital personnel and
other medical personnel as well as laboratory personnel.

All autoclave users must receive training in proper usage from an experienced
employee. Every new employee must undergo a training period under an
experienced employee.

1.7 Warranty Description

This warranty does not include routine cleaning and preventive
maintenance, to be performed according to instructions in chapter 8.

Tuttnauer warranties all new autoclaves to be free from defects in material and
workmanship for a period of two (2) years, covering the parts (except door
gaskets and air filters – they are considered wear items).

Tuttnauer warranties all chambers for a period of ten (10) years against defects
in materials and workmanship.

This warranty does not apply to any product that has been subjected to misuse,
neglect, accident or improper installation or application, nor shall it extend to
autoclaves that have been repaired or altered outside the factory without prior
authorization from Tuttnauer.

Tuttnauer’s obligation is limited to the repair or replacement of parts for the
autoclave. This warranty will be void if the unit is not purchased from an
authorized Tuttnauer dealer. No other warranties or obligations are expressed
or implied.

1.8 Warranty Statement

The warranty registration must be completed and returned to our service
departments; within fourteen (14) days of purchase or the warranty will be void.

Page 7

Summary of Contents for AMS11-120-T










































































































Reviews: