34
Code
Meaning
Range
T Description
See also the acquisition procedure described in the ‘Maintenance’ section.
BTE
BlueTooth
Enabling
NO, YES
C
R
BLUETOOTH
TM
Enabling
.
NO the
BLUETOOTH
TM
interface is disabled.
YES the
BLUETOOTH
TM
interface is enabled: the detector can communicate with a
PC equipped with a compatible interface.
CH
Transmission
channel
0 - 99
C
R
Transmission channel.
Select a proper channel to synchronize a multiple installation or to
reject environmental electrical interference.
0 - 49 for 50Hz power supply.
50 - 99 for 60Hz power supply.
CR
Alarm counter
reset
-
C
Equipment fitted with photocells only.
Alarm counter reset. This command requests confirmation.
NOTE: there are two counters, one at operator level and one at supervisor level: only the
counter at the current level of programming is reset.
EN
Environmental
electromagneti
c noise
measurement
NO, YES
C Displays the value of the electromagnetic environmental noise.
This function is activated by pressing the ENTER key: the numeric values will then appear
on the right, from 0 to 99, continually updated. To end measurement, press any key.
NOTE: if both GN and EN functions are activated, function EN has priority.
NOTE: the function is terminated automatically after 2 minutes.
EVA
Environmental
vibration
acquisition
-
C It activates the procedure for acquiring the environmental mechanical vibrations; this
procedure is described in detail in the ‘Maintenance’ section.
See also the AVS parameter.
HE
HELP
-
R
Function available in remote mode only.
This selects a display of the meaning of the available programming functions. The read-out
will give the correspondence table (function – function code).
The * character indicates that the command is enabled at user level (see the UP
command).
IP
IP Address
xxx.xxx.xxx.xxx
R Command available only if a network adapter APSIM is installed.
Read only function. Current IP address of the WTMD. It is displayed in two steps.
Ex.: IP address 192.168.0.101:
IP
I192.168
.0.101
IS
International
Security
Standard
1-30
C
R
Selects a security level corresponding to an international standard.
During normal operation the current Security Level is displayed by pressing the
key.
NOTE: in remote programming, an IS status request provides the complete list of available
settings and the current value.
Example:
#IS
<enter>
NILECJ1
NILECJ2
:
:
CURRENT SETTING: NILECJ2
NOTE:
If the selected setting has been modified affecting detection capability, an additional ‘MODIFIED’
indication appears.
If the current setting does not correspond to any Security levels pre-memorised in factory, a ‘NO SET’
message is provided.
If an LD user-defined setting is selected, a previous IS setting is disabled. This also is signalled through
the message ‘NO SET’:
The available Security Levels are listed in detail in the ‘Factory Acceptance Test Report ‘ form included.
LBI
Alarm
indication
enabling at the
entry side LED
bar
ON
OFF
C
R
Alarm indication enabling at the entry side LED bar.
ON
the entry side LED bar provides an indication in case of an alarm
OFF
the entry side LED bar does not provide an indication in case of an alarm.
NOTE: the entry and exit sides of the archway are defined by the GD parameter.
LC
Uniformity
coefficient of
the
electromagneti
c field emitted
by the antenna
- ground level
-20,…,-1,
0,
1,…,20
C
R
Uniformity coefficient of the electromagnetic field emitted by the antenna at ground level. It
allows the sensitivity equalization, due to metal reinforcement bars located inside the floor
-20
maximum field attenuation
0
no change (standard)
+20
maximum field increment
This command is available on certain probe models only.
LD
Loading user-
defined
settings
0-19
C
R
Loading of a setting predefined according to the customer’s requirements.
Besides the IS settings, which are compliant to security international standards, the LD
settings can be used to select special operating modes specified by the customer.
NOTE: in remote programming, an LD status request provides the complete list of the available settings
and the current name.
Example:
#LD
0<enter>
selection of LD=0 setting
#LD
<enter>
303-670-1099
