TURFCO TurnAer-26 Operator'S Manual, Maintenance Manual, Parts List Download

Page: 3 / 17

™

Speciﬁcations

Intended Use:

The TurnAer-26 is a self-propelled, steerable, coring tine aerator. The TurnAer-26 is

intended to be used for the aeration of the turf or soil at a properly prepared worksite. The TurnAer-26

is NOT intended to be used for any purpose other than the aeration of turf. The TurnAer-26 is NOT designed

for or intended to accept riders.

Aerating Speed

..........Up to 110 Meters Per Minute (359 Feet Per Minute) (21,557 Feet Per Hour)

at 6.6 Km/h (4.1 MPH)

Aerating Rate

.............Up to 4068 sq. meters Per Hour (4865 sq. yd.) (43,787 Sq. Ft. Per Hour)

Aerating Depth

...........Up to 70 mm (2-3/4” Inches)

Aerating Width

...........0.619 Meter (24-3/8” Inches)

TurnAer-26 Width

.......0.897 Meter (35-5/16” Inches)

TurnAer-26 Length

.....0.99 Meter (39” Inches) Handlebars In Folded Storage Position

1.473 Meter (58” Inches) Handlebars In Operating Position, Wheels Down

TurnAer-26 Height

......0.914 Meter (36” Inches) In With Handlebars Folded Storage Position

1.295 Meter (51” Inches) With Handlebar In Operating Position (Middle

Height Setting), Wheels Lowered (Transport Wheels Down)

0.99 Meter (39” Inches) With Handlebar In Operating Position (Middle

Handlebar Height Setting), Wheels Raised (Transport wheels Raised)

Weight

........................152 Kg (335 Pounds)

Engine

.........................Product Number 85370 - Honda 2.98 kW (4.0 HP) GX120 With 6:1 Gear Reducer

Drive

............................V-Belt to Differential, RC-40 Roller Chain to Tines Reels and Front Drums

Clutch

.........................Belt Idler Type, Controlled From Operating Position

Tines

...........................Coring Type, 19 mm Diameter (3/4” Inch) Heat Treated Alloy Steel

V-Belt

..........................Goodyear B48F 85510

Chain

...........................RC-40 Roller Chain

Bearings

.....................Flange Mounted Self-Aligning Sealed Ball Bearings

Wheels

........................8” x 2.5” Inch Semi-Pneumatic Rib Tread Tires With 5/8” Roller Bearings

Registered Trademarks and Patents

TurnAer-26™

is covered under U.S. Patent 6,708,773

Additional Patents Pending

TurnAer-26™

is a trademark on Turfco Mfg., Inc.

TURFCO

is a registered trademark of Turfco Mfg., Inc.

Vibration and Noise Emission Levels

Vibration Level:

Operator Position

on Handlebar =

0.41 m/s2 RMS

Operating Conditions:

Full Throttle, Operating

Noise Emission Level:

Operator Position

Sound Pressure (LpA) =

87.5 dBA

Sound Pressure Level (LwA) =

97 dBA

Operating Conditions:

Full Throttle, Stationary, Aerator Operating

WARNING

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

ONLY OPERATE ENGINE IN AREAS WITH ADEQUATE VENTILATION.

DO NOT OPERATE ENGINE IN ENCLOSED AREAS.

SPECIFICATIONS

Summary of Contents for TurnAer-26


















Search results

Summary of Contents for TurnAer-26

Reviews:

Related manuals for TurnAer-26

Brands by name

Popular brands

TURFCO TurnAer-26, Operator'S Manual, Maintenance Manual, Parts List

Search results

Summary of Contents for TurnAer-26

Reviews:

Related manuals for TurnAer-26

Brands by name

Popular brands