TURFCO TurnAer-26 Operator'S Manual, Maintenance Manual, Parts List Download Page 14

Page: 14 / 17

™

TO AVOID SERIOUS INJURY,

Do Not Lubricate Or Adjust The

TurnAer-26 With the Engine Running.

Remove The Wire From The Spark

Plug.

All Of The Following Lubrication And Adjustment

Procedures Involve Or Are Near Rotating Part And

Moving Parts. Follow All Safety Precautions And

Wear The Appropriate Safety Gear.

LUBRICATION

Transport Wheels:

Grease ﬁttings on transport wheels

after every 8 hours of operation.

Drive Train Components, Chain, Sprockets, And

Pivot Points:

All bearings in the drive train require

no lubrication. Periodic inspection should be done

to insure that any worn bearings are detected and

replaced. The chains requires no lubrication. Protect

chains from rust and moisture with a very light coating

of machine oil. The chain sprockets should be cleaned

of any dirt build-up to ensure proper chain contact.

Periodically inspect the chain and sprockets for wear

or damage. Replace if necessary. Periodically clean

the entire machine of dirt, grease and grass build-up

and lubricate all pivot points with light machine oil.

Engine and Gear Reducer:

CHECK OIL LEVELS

DAILY.

Follow the engine manufacturer’s manual for

intervals of oil change, proper oil types, and ﬁll levels

for the engine and the gear reduction unit.

ADJUSTMENTS

Check and retighten nuts and screws frequently to

ensure safe operation.

Chain Idler Sprocket Adjustment (See Figure 6):

The chain idler sprockets (one located under each side

chain guard) can be adjusted to remove excess slack

in the drive chains caused by chain wear or stretch.

Remove side guards. Before adjusting idler sprocket

position, ensure that the chain and all sprockets have

been cleaned and that the chain seats properly on

the sprockets. A build-up of dirt on the sprockets or

chain can cause the chain to become too tight. Inspect

all the sprockets, bearings, and the chain for wear or

damage.

Step 1.

Remove both side guards and elevate tine reels.

Step 2.

Loosen the idler sprockets. Move idler

sprockets along adjusting slot until the chain has an

SERVICE

CLUTCH

CABLE

ADJUSTER

CLUTCH

IDLER

PULLEY

IDLER

CHAIN

SPROCKET

1/2" TO 3/4" UP AND DOWN MOVEMENT

1/2" TO 3/4"

STRETCH

FIGURE 6

BELT STOP

BRACKET

SV85370-01

Service

WARNING

SAFE-12

Summary of Contents for TurnAer-26


















Search results

Summary of Contents for TurnAer-26

Reviews:

Related manuals for TurnAer-26

Brands by name

Popular brands

TURFCO TurnAer-26, Operator'S Manual, Maintenance Manual, Parts List

Search results

Summary of Contents for TurnAer-26

Reviews:

Related manuals for TurnAer-26

Brands by name

Popular brands