background image

  

9

  

Service and maintenance

Do not work underneath the lifted sweeping 
machine.

•  Drive carrier vehicle backwards. Lower the sweeping 

machine frame onto the rear support rollers and park the 
vehicle.

Secure the carrier vehicle against unintended 
restart and movement!

•  Unscrew the four countersink screws (23) and place 

them on the side, together with the holding plate (24).

•  Pull off worn-out brush rings.

Beeline brush rings

•  Slide the new brush rings (25) onto the drum shaft (7), 

such that a honeycomb-like structure appears.

•  The brush rings must be pushed onto the drum shaft 

(7) in such a way that the groove (26) sits on the drivers 
(27).

Sunline brush rings

•  Push the new brush rings alternatingly onto the brush 

shaft (7) (corrugated wire (28), spacer (29), plastic (30), 
spacer (29), corrugated wire (28), …)

•  The brush rings must be pushed onto the drum shaft (7) 

in such a way that the groove (31) sits on the driver (27).

•  Before assembly, clean all parts and replace if 

necessary.

When ordering spare parts, please specify the type 
label, serial number and the year of construction of 
the machine. For article numbers refer to the list of 
spare parts.

•  The assembly of the drum shaft is carried out in the 

opposite order to the disassembly.

The chain wheels must be mounted in such 
a way that the cogs align.

The chain joint must be closed in the running 
direction of the chain.

Adjustment of chain tension: see Chapter 7.5 
Tightening chain.

See Chapter 5.8 for adjustment of the 

sweeping proile

N O T E

N O T E

N O T E

ATTENTION

ATTENTION

Beeline brush 

rings

Brush rings 

50 % PP / 

50 % Corrugated wire

Driv

e sid

e

Summary of Contents for Kompakt HD 400 Series

































































Reviews: