Tuchel Kompakt HD 400 Series Operating Manual Download Page 7

Page: 7 / 64

Inhaltsverzeichnis

Detachment ...................................................... 9

6.1 Deinstallation in general ...................................... 39

6.2 Detachment - coupling triangle............................ 40

6.3 Detachment - 3-point linkage .............................. 40

6.4 Detachment - yard loader .................................... 40

6.4 Detachment - other carrier vehicles .................... 40

7 Service and maintenance ...............................

7.1 General ............................................................... 41

7.2 Side broom readjustment .................................... 42

7.3 Replacement of the Vulkollan rail ........................ 42

7.4 Replacing the plate broom .................................. 43

7.5 Water spraying device ......................................... 44

7.6 Tightening the chain ............................................ 44

7.7 Replacement of the overload protection

7.8 Replacing sweeping drum for Kompakt ø 400

Disassembly on the bearing side ..................................46
Disassembly on the drive side / chain case ..................46

7.9 Replacing sweeping drum for Kompakt ø 400

Disassembly on the bearing side ..................................48
Disassembly on the drive side / chain case ..................48
Beeline brush rings .......................................................49
Sunline brush rings .......................................................49

7.10 Replacing sweeping drum for Kompakt ø 520

Disassembly on the bearing side ..................................50
Disassembly on the drive side / chain case ..................50

7.11 Replacing sweeping drum for Kompakt ø 520

Disassembly on the bearing side ..................................52
Disassembly on the drive side / chain case ..................52
Beeline brush rings .......................................................53
Sunline brush rings .......................................................53

7.12 Lubrication plan ................................................... 54

Lubricating points - sweeping machine .........................54
Lubricating the chain .....................................................55
Lubricating the drive shaft .............................................55
Gearbox lubricant ..........................................................55

7.13 Malfunctions; causes and rectiication

................. 56

Summary of Contents for Kompakt HD 400 Series

































































Search results

Summary of Contents for Kompakt HD 400 Series

Reviews:

Related manuals for Kompakt HD 400 Series

Brands by name

Popular brands

Tuchel Kompakt HD 400 Series, Operating Manual

Search results

Summary of Contents for Kompakt HD 400 Series

Reviews:

Related manuals for Kompakt HD 400 Series

Brands by name

Popular brands