manualshive.com logo in svg

Tuchel Kompakt HD 400 Series, Operating Manual

Share
Download
Tuchel Kompakt HD 400 Series Operating Manual Download Page 40

Detachment

0

.  Detachment - coupling triangle

Before carrying out the following tasks irst read 

the safety instructions in Chapter 2 - Safety. 
Also, familiarise yourself with the task sequence 
described.

•  Unlock the lock of the coupling triangle and lower the 

coupling triangle from the carrier vehicle.

•  Drive vehicle backwards.

.  Detachment - -point linkage

Before carrying out the following tasks irst read 

the safety instructions in Chapter 2 - Safety. 
Also, familiarise yourself with the task sequence 
described.

•  Remove the 3-point linkage rods from the carrier vehicle 

at the 3-point linkage of the sweeping machine.

•  Drive carrier vehicle backwards.

.  Detachment - yard loader

Before carrying out the following tasks irst read 

the safety instructions in Chapter 2 - Safety. 
Also, familiarise yourself with the task sequence 
described.

•  Unlock the receptacle as described in the carrier 

vehicle's operating manual.

•  Lower the receptacle of the carrier vehicle and drive 

back vehicle.

.  Detachment - other carrier vehicles

Before carrying out the following tasks irst read 

the safety instructions in Chapter 2 - Safety. 
Also, familiarise yourself with the task sequence 
described.

•  Unlock the receptacle as described in the carrier 

vehicle's operating manual.

•  Lower the receptacle of the carrier vehicle and drive 

back vehicle.

Summary of Contents for Kompakt HD 400 Series

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands