Tsubaki SHOCK RELAY TSBSC Series, Instruction Manual

Page: 5 / 16

䇲
5
䇲
㸴 㸴
. Installation method
6.1 Installation environment
Make sure to install Shock Relay at the environmental condition shown in the attached table.
6.2 Main unit
(1) Installation with screw
Put the plate for installation at the both side of Shock Relay, and install Main unit to the panel.
(2) Installation with DIN Rail
While pulling the hook of Shock Relay to the arrow direction, install Shock Relay to 35mm DIN rail.
When removal, pull the hook to the arrow direction with flathead screwdriver.
6.3 Panel unit
(1) Loosen and remove the screw which fix the lid
backside.
(2) Hold the panel with the panel unit and lid backside,
and fix with screw.
㻌
7. Wiring method
㻔㻝㻕㻌㼁㼟㼑㻌㼏㼛㼙㼙㼑㼞㼏㼕㼍㼘㻌㼜㼛㼣㼑㼞㻌㼟㼛㼡㼞㼏㼑㻌㼒㼛㼞㻌㼛㼜㼑㼞㼍㼠㼕㼛㼚㻚㻌
㻌 㻌 㻌 㻌 㻌 㻌 㻌 㻿㼑㼠㻌㼠㼔㼑㻌㼕㼚㼟㼡㼘㼍㼠㼕㼛㼚㻌㼠㼞㼍㼚㼟㼒㼛㼞㼙㼑㼞㻌㼕㼚㻌㼏㼍㼟㼑㻌㼠㼔㼍㼠㻌㼠㼔㼑㼞㼑㻌㼕㼟㻌㼔㼕㼓㼔㻌㼒㼞㼑㼝㼡㼑㼚㼏㼥㻌㼚㼛㼕㼟㼑㻌㼓㼑㼚㼑㼞㼍㼠㼛㼞㻌㼟㼡㼏㼔㻌㼍㼟㻌㼕㼚㼢㼑㼞㼠㼑㼞㻚㻌
㻔㻞㻕㻌㻹㼍㼗㼑㻌㼟㼡㼞㼑㻌㼠㼔㼑㻌㼒㼛㼘㼘㼛㼣㼕㼚㼓㼟㻌㼍㼒㼠㼑㼞㻌㼠㼔㼑㻌㼏㼛㼙㼜㼘㼑㼠㼕㼛㼚㻌㼛㼒㻌㼏㼛㼚㼚㼑㼏㼠㼕㼛㼚㻌㻔㼣㼕㼞㼕㼚㼓㻕㻌
㻌
㻌 㻌 㻌 㻌 㻌㻌 㼍㻚㻌㼃㼕㼞㼕㼚㼓㻌㼕㼟㻌㼏㼛㼞㼞㼑㼏㼠㻫㻌
㼎㻚㻌㻺㼛㼠㼔㼕㼚㼓㻌㼒㼛㼞㼓㼑㼠㼒㼡㼘㻌㼛㼚㻌㼣㼕㼞㼕㼚㼓㻫㻌
㻯㻚㻌㻺㼛㻌㼟㼔㼛㼞㼠㻙㼏㼕㼞㼏㼡㼕㼠㻌㼛㼞㻌㼑㼍㼞㼠㼔㻌㼒㼍㼡㼘㼠㻌㼎㼑㼠㼣㼑㼑㼚㻌㼠㼑㼞㼙㼕㼚㼍㼘㼟㻛㼣㼕㼞㼑㼟㻫㻌 㻌
㻌
㻔㻟㻕㻌㻿㼡㼕㼠㼍㼎㼘㼑㻌㼣㼕㼞㼑㻌
㼃㼕㼞㼑㻦㻌㻵㻿㻻㻌㻝㻌㼠㼛㻌㻞㻚㻡㻌㼙㼙
㻞
㻘㻌㻭㼃㻳㻏㻝㻤㻌㼠㼛㻌㻝㻠㻌㻣㻡䉝㻌 㻯㼛㼜㼜㼑㼞㻌㼣㼕㼞㼑㻌
㻿㼠㼞㼕㼜㻌㼘㼑㼚㼓㼠㼔㻦㻌㻤㻌㼙㼙㻌
㻺㼡㼙㼎㼑㼞㻌㼛㼒㻌㼏㼛㼚㼚㼑㼏㼠㼕㼛㼚㻦㻌㻭㼠㻌㼙㼛㼟㼠㻌㻞㻌㼣㼕㼞㼑㼟㻌㼍㼠㻌㻝㻌㼠㼑㼞㼙㼕㼚㼍㼘㻌
㼀㼕㼓㼔㼠㼑㼚㼕㼚㼓㻌㼠㼛㼞㼝㼡㼑㻦㻌㻜㻚㻤㻌㼠㼛㻌㻝㻚㻞㻌㻺䞉㼙㻌
● wiring must be carried out by skilled and
professional engineers.
● Before starting the operation, turn power on/off.
Otherwise electrical shock may occur.
㻌㻌
㻴㼛㼛㼗 㻌
㻤㻞㻚㻟㻌
㻞㻙㻹㻠㻌
㻭㼠㼠㼍㼏㼔㼙㼑㼚㼠 㻌
Warning
!