Tsubaki LINIPOWER Instruction Manual Download Page 29

Page: 29 / 37

5 to 7 pieces of Liners are at each stud bolt

⑦

with a distance collar

⑨

Remove the liner

⑧

evenly from the each stud bolt according with measured gap. Adjust the

thickness to reach the specified gap.

【

Note

】

Keep the removed liners

⑧

Return the yoke

①

back to the original position. Securely tighten the hexagon bolts

⑩

After

tightening the hexagon bolts

⑩

, remove the hexagon bolts (M8X50).

Check the gap at several points along the circumference and all in range of specified value. The yoke

①

and the armature

③

should be installed parallel position. After adjusting the gap, apply power

and make sure the brake function correctly. When the gap is too small between Armature

④

, Brake

plate

⑪

and Lining

⑤

each parts contact and make noise during rotation.

Fix the brake cover

⑯

【

Note

】

Be aware of wire, packing is installed correctly, no twist on wire or packing. If not set

correctly while fixing brake cover

⑯

it may not keep proper water protection.

Summary of Contents for LINIPOWER




































Search results

Summary of Contents for LINIPOWER

Reviews:

Tsubaki LINIPOWER, Instruction Manual, Page: 29 / 37

Search results

Summary of Contents for LINIPOWER

Reviews: