Tsubaki LINIPOWER Instruction Manual Download Page 25

Page: 25 / 37

■

0.75kW / 1.5kW/ 2.2kW

It is usually sufficient to monitor the operational status of the brake, but be aware of the following while brake

function is not well:



This brake works with friction force between the brake plate

⑥

, the armature

③

and the lining

⑤

brake lining will be worn while operation. It is necessary to change brake plate

⑥

, the armature

③

and

the lining

⑤

after 3 times of ‘Gap adjustments’.



It is necessary to clean up the brake every 6 months because it will have wear of dust and

particles due to the brake operation.

(1) Brake structure

(2) Brake inspection and gap adjustment

1) Loosen the bolts

⑧

for brake cover and remove the brake cover

⑨

2) Tighten Adjustable nuts

⑩

(3 pcs.) clockwise, and adjust the gap to range listed below with

verifying the gap dimensions with a thickness gauge.

Check the gap at several points along the circumference to be the Fixed core

④

and Armature

③

are

parallel to each other, then apply locking agent. (Do not repeat loosening and tightening, the

adjustable nuts

⑩

may damage to the nuts and lose locking effect.)

【

Note

】

・

Before tightening the adjustable nuts

⑩

, insert the hexagon socket screw key into the hexagon socket

of the guide bolt so that the guide bolt may not come loose by rotating together.

・

Replace with a new adjustable nut

⑩

if the adjustable nut

⑩

is removed or repeatedly tightened and

loosened. (Size 0.75kW:M5

P0.8, 1.5,2,2kW:M8

P1.25 ) Remove grease from the guide bolt

⑬

and

the adjustable nut

⑩

, and apply anti-loosening liquid in this case. Do not take down the brake

because it may make reassembly impossible and incorrect reassembly may lead to a brake

malfunction.

3) After adjusting the gap, make sure the brake operates normally by connecting to power source.

Observe the gap is appropriate to prevent the armature

③

, brake plate

⑥

and lining

⑤

from

contacting during rotation. If they do come in contact, readjust the gap.

4) Attach the brake cover

⑨

with bolts

⑧

Gap

External gap

★

⑥

Brake plate

⑦

Seal washer

⑧

Bolts for brake cover

⑨

Brake cover

⑩

Adjustable nuts

⑪

Hub

①

Bolts for manual release

(+Pan head machine screw)

②

Double nuts

③

Armature

④

Fixed core

⑤

Lining

⑫

Water proof packing

⑬

Guide bolt

Summary of Contents for LINIPOWER




































Search results

Summary of Contents for LINIPOWER

Reviews:

Tsubaki LINIPOWER, Instruction Manual, Page: 25 / 37

Search results

Summary of Contents for LINIPOWER

Reviews: