Tryton TJB110, Operating Instruction

Page: 9 / 60

9
DEVICE COMPONENTS:
1.
2. On/off switch
3. Main handle
4.
5. Adjustable handle
6. Lock knob
7.
8.
9. Telescopic shaft
10. Head release button
11. Grass trimmer head
12. Plant protector
13. Safety guard
BEFORE USE:
14. Battery lock button*
The grass trimmer is delivered in a cardboard box partially assembled.
15. Spool holder
After removing the packaging, check whether all parts have been
16. Charger*
delivered and assemble necessary parts as instructed in the manual.
17. Adapter *
NOTE:
18. Battery level indicator button*
Make sure the battery is disconnected before any assembly or
19. Battery level indicator*
adjustments.
20 . Spool button
n
Installation of the safety guard
21. Trimmer line
22. Line cutter
24. Line spool
25. Spool cover
26. Spool holder release button
You can check the battery level with the battery level indicator button
A single LED means the battery level is low, two
LEDs mean medium level, and three LEDs mean full battery.
Trimming diameter 230 m m
Trimmer line round ø 1,5 mm
Connect the battery to the charger
Connect the adapter plug to the charger
Connect the adapterto a mains socket
Connect the battery to the charger
Battery charging indicator
A green LED light indicates that the charger is connected to a power
source. After the battery is connected, the red LED is on to indicate
work tools, assurance of proper hand temperature, or determination of
the sequence of work operations.
The numbering of device elements refers to the drawing on pages 2- 4 of the
instruction manual: The declared total vibrations and declared noise emissions were
measured in accordance with a standard test method and may be used
Fig.A Battery *
for tool comparison.
The declared total vibrations and noise emissions can be used in
preliminary exposure assessment.
Warnings:
The vibrations and noise emissions during the actual use of the power
tool may differ from the declared values depending on how the tool is
used and on the type of the workpiece in particular.
Determine safeguards to protect the operator. They should be based on
the estimated exposure under actual operational conditions (taking into
account all parts of the operating cycle such as when the tool is switched
off or idle except the start time).
Fig.C
Fig.D
Fig.G
Install the safety guard ( 13 ) before use. Slide the guard on the trimmer
head ( 11 ), and then secure it with two screws provided with the device
Fig.I
(see Fig. C , page 2).
Fig.J
n
Charging the battery
NOTE! Battery and charger are not part of the delivery . Depending on your
* The accessories shown or described are not standard equipment.
needs, you can purchase a 1.5 Ah battery TJ15AK , 2.0 Ah battery TJ2AK or
For the complete offer of auxiliary equipment, see our
4.0Ah TJ4AK and a compatible charger TJ3LD (charging time 3–5 hours)
catalogue.
or TJ1LD (charging time 1 hour).
TECHNICAL DATA :
( see Fig. D , page 3)
Supply voltage 20 V d.c.
Charge the
Rotation speed under no-load conditions
battery fully before use.
TJ3LD
The first charging procedure using TJ3LD should last at least 5
Weight (with battery) 2,2 kg
hours.
Acoustic pressure level (LpA) 74 dB(A) 1. If the battery ( 1 ) was connected to the trimmer, press the battery lock
button ( 14 ) and remove it ( see Fig. A2 , page 2).
Acoustic power (LwA) 90,28 dB(A)
2. ( 1 ) ( 16 ) ( see Fig. D , page 3).
T olerance of measurements K /K 2,5dB(A)/0,4 dB(A)
LpA LwA
3. ( 17 ) ( 16 ).
4. 11 0-240 V, 50 -60 Hz.
TJ1LD
The first charging procedure using TJ1LD should last at least 1 hour.
1. If the battery ( 1 ) was connected to the trimmer, press the battery lock
The vibration level value given refers to basic application of the tool. If the
button ( 14 ) and remove it ( see Fig. A2 , page 2).
tool is used for other applications or with other tools, or if it is not
2. ( 1 ) ( 16 ) ( see Fig. E , page 3).
maintained properly, the vibration level may differ from the values given.
3. Connect the charger plug to a mains socket 220-240 V, 50Hz.
The above-mentioned causes may lead to higher exposure to vibrations
n during the whole work time.
One must implement additional safety measures to protect the operators
from exposure to vibrations, such as maintenance of the electric tool and
Safety button
Release button
Clamping ring
23. Spool holder base
( 1 8 ) .
Charger
Charger
8000 /min
Mean vibration acc. to EN 50636-2-91
2
( - 1,5m/s ) a
h
t olerance of measurements
2
3,436 m/s
Recommended 20 V Li-ion batteries: TJ15AK (1,5Ah), TJ2AK (2Ah), TJ4AK (4Ah)
Recommend chargers: TJ3LD (3-5h), TJ1LD (1h)