Trycom Technology TRP-C32S User Manual Download Page 9 | Manualshive

Page: 9 / 28

background image

9

installation is complete user may access to the Manager software in the program files. If loaded in

the default location Go to

Start/Programs/Trycom/TRP-C3X

Manager to open.

6. Updating an Existing Installation

If an older version of the Manager software is already installed, the Modify, repair or remove the

program window will appear when the installation process is initiated. The recommended

procedure is to remove all installed components first. Once the software has been removed,

install the new software.

Highlight remove

.

7. How to configure TRP-C32S

There are 4 ways to access the Server Properties and program the TRP-C32S

1. TRP-C3X Manager software, see 7-1.

2. Console mode, see 7-2.

3. Telnet, see 7-3.

4. Web Server, see 7-4.

7-1. Using TRP-C3X Manager Software

The

“TRP-C3X Manager”

software performs several functions:

A: Searching for TRP-C32S connected to the network

B: Displaying and changing the configuration of TRP-C32S

C: Installing virtual COM ports on a computer

D: Displaying and configuring virtual COM ports

E: Uninstalling virtual COM ports on a computer

F: Upgrading the TRP-C32S firmware

«
...
7
8
9
10
11
...
»

Summary of Contents for TRP-C32S





























Reviews:

No comments

Related manuals for TRP-C32S

Brand: XINDAK Pages: 8

Brand: La Marche Pages: 15

Brand: Samson Pages: 58

BML-S1G0-B7 Series

Brand: Balluff Pages: 20

Brand: Humandata Pages: 10

Brand: Black Box Pages: 16

Brand: Extron electronics Pages: 8

SINUS CABINET K Series

Brand: Elettronica Santerno Pages: 226

Brand: Wacker Neuson Pages: 36

L.O.C.PRO LP7-2

Brand: PAC Pages: 2

Brand: GALCO Pages: 8

Brand: Magtek Pages: 54

Brand: AV Link Pages: 2

Brand: Metra Electronics Pages: 9

Brand: Daewoo Pages: 27

Brand: DX Engineering Pages: 4

Brand: UCEC Pages: 22

Brand: Telair Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands