Trycom Technology TRP-C32S User Manual Download Page 11 | Manualshive

Page: 11 / 28

background image

11

7-1-2.Configuring Server Properties

Highlight the serial server in the Serial Server List window and double click to open the

Server Properties window. The Server Properties window is used to configure and store the

Server configuration settings. Details for setting Properties are described in the next chapter.

After configuring as needed, click Update to store the configuration in the server and click

“Yes” to restart the server to make sure all settings are changed to conform to the desired

application.

«
...
9
10
11
12
13
...
»

Summary of Contents for TRP-C32S





























Reviews:

No comments

Related manuals for TRP-C32S

Brand: Paradox Pages: 28

Brand: Daikin Pages: 4

Brand: Enerdrive Pages: 24

Brand: Versus Audio Pages: 12

Brand: xpr Pages: 12

Brand: Statpower Pages: 28

Interface Module XC Modbus

Brand: Baer Pages: 10

Brand: Helvest Pages: 2

S-1000MM-M2xx05

Brand: Perle Pages: 12

Basys Controls QD1010b

Brand: TCS Pages: 5

Media Giant CM3G Series

Brand: Conceptronic Pages: 2

Brand: Lambda Pages: 47

Brand: Speaka Professional Pages: 8

DIGITAL plus LC100

Brand: Lenz Pages: 8

Brand: Xnexus Pages: 20

Brand: B PLUS TV Pages: 10

Brand: ZIPPER MASCHINEN Pages: 52

FR-S520-0.1K to 3.7K(-R)(-C)

Brand: Mitsubishi Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands