10
EN
vertical heater TAC XT 18 / TAC XT 27
8. Ensure that the pipe or tube and the hood are tightly
secured.
ð
Ensure that the pipe or tube connected is heat-resistant.
Connection example:
13
Start-up
When positioning the device, observe the minimum distance
from walls or other objects as described in the chapter
Technical annex.
A
B
C
C
D
•
Before restarting the device, check the condition of the
power cables. If there are doubts as to their sound
condition, contact the customer service.
•
The device may only be used in environments with no
excessive formation of dust.
•
Set the device up in an upright and stable position.
•
Position the device on even, stable and heat-insensitive
ground in a way to prevent it from tipping over.
•
When setting up the device, ensure a sufficient distance
for air inlet and outlet as well as for operation (see
Technical data).
•
Do not create tripping hazards when laying the power
cables or other electric cables, especially when positioning
the device in the middle of the room. Use cable bridges.
•
Make sure that extension cables are completely unrolled.
•
Make sure that no curtains or other objects interfere with
the air flow.
•
Make sure that the device cannot come into contact with
moisture or water.
Inserting the air filter
Note
Do not operate the device without an air filter inserted
into the air inlet!
Without the air filter, the inside of the device will be
heavily contaminated. This could reduce the
performance and result in damage to the device.
•
Make sure that the air filter is installed before switching
the device on.
Attaching a flowstop shutter
The optional flowstop shutters can be attached to one of the
four insides of the tower. This prevents up to three sides of the
tower from discharging air, e.g. if discharged air is not desired
or not required on the respective side(s).
Connecting the power cable
•
The device is provided with two power cables. If you only
connect one power cable to the an power connection 1 (
5
),
the TAC XT 18 only supplies 9 kW and the TAC XT 27
supplies 18 kW. Connection of the second power cable to
power connection 2 (
4
), the devices will supply their
maximum power. The device can be operated with a
generator with sufficient capacity. Take into consideration
that the heat output of the device is controlled, so that the
generator connected has to adapt to the control. Ensure in
advance whether the generator complies with the power
supply of the device.
4
5
Summary of Contents for TAC XT 18
