8
GB
Operation / Accessories / Maintenance
USING THE SANDING FRAME
• We recommend that you begin by
sanding against the grain
• Start the sander facing at 10 or 11
o’clock, and move it back and forth
across the workpiece slowly. Finish by
sanding parallel to the grain
ACCESSORIES
MAINTENANCE
• A full range of different grit sanding belts and accessories is
available from your Triton stockist. Spare parts can be obtained from
toolsparesonline.com
WARNING
: Always disconnect from the power supply before carrying out any
inspection, maintenance or cleaning.
GENERAL INSPECTION
• Regularly check that all the fixing screws are tight. They may vibrate loose
over time
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Triton service centre. This
advice also applies to extension cords used with this tool
CLEANING
WARNING
: ALWAYS wear protective equipment including eye protection and
gloves when cleaning this tool.
• Keep your tool clean at all times. Dirt
and dust will cause internal parts to
wear quickly, and shorten the device’s
service life
• Clean the body of your machine with a
soft brush, or dry cloth
• Never use caustic agents to clean
plastic parts. If dry cleaning is not
sufficient, a mild detergent on a damp
cloth is recommended
• Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through the ventilation
holes (where applicable)
LUBRICATION
• Slightly lubricate all moving parts at regular intervals with a suitable spray
lubricant
CHANGING THE DRIVE BELT
Note
: A spare drive belt is supplied with
the sander. Further replacements and
other spare parts are available from your
Triton stockist or from toolsparesonline.
com.
1. Using a Phillips screwdriver, remove
the screw holding the Drive Belt Cover
(5) in place
2. Remove the worn belt by easing it off
the bottom larger drive pulley, and then lift away
3. Clean all dust and debris away
4. Place new drive belt over the top drive pulley and push onto the larger
pulley, then rotate the belt until it is on both pulleys and located in the
grooves of each pulley
5. Place the drive belt cover back on and screw the fixing screw tight
STORAGE
• Store this tool carefully in a secure, dry place out of the reach of children
DISPOSAL
Always adhere to national regulations when disposing of power tools that are
no longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic
equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct
way to dispose of power tools
Summary of Contents for TA 1200BS
