TRISTAN TECHNOLOGIES SMM-770 Operating Manual Download

Page: 71 / 76

Model SMM 770 Scanning Magnetic Microscope System

TRISTAN TECHNOLOGIES --Page

Default software filter FIR windowing. Either "None", "Hanning", "Hamming",
"Triangular", "Blackman", "ExactBlackman", "BlackmanHarris", "KaiserBessel", or
"FlatTop"

Hi_Cutoff_(Hz)=37

Default software filter high-frequency cutoff.

Lo_Cutoff_(Hz)=25

Default software filter low-frequency cutoff.

PB_Ripple_(dB)=1

Default software filter pass-band ripple.

SB_Attenuation_(dB)=90

Default software filter side-band attenuation.

IIR_Order=3

Default software filter IIR order. Allowed range is 0 to 3.

FIR_Taps=10

Default software filter FIR taps. Allowed range is 0 to 100.

Zero_Phase=FALSE

Default software filter zero-phase enable/disable. Either "TRUE" or "FALSE".

[Display]

Amp_Units=Pk-Pk

Either "Pk-Pk" or "RMS".

Angle_Units=Degrees

Either "Degrees" or "Radians".

FFT_Averaging=None

Either "None", "Vector", "RMS", or "PeakHold".

FFT_Weighting=Exponential

Either "Linear" or "Exponential".

FFT_AvgNum=10

Number of running averages for the FFT display.

FFT_Window=None

Either "None", "Hanning", "Hamming", "BlackmanHarris", "ExactBlackman", "Blackman",
"FlatTop", "4TermBHarris", "7TermBHarris", or "LowSidelobe".

Type=Sample

Default 3D display type. Either "Sample", Reference", or "SampleVsReference".

Summary of Contents for SMM-770













































































Search results

Summary of Contents for SMM-770

Reviews:

Related manuals for SMM-770

Brands by name

Popular brands

TRISTAN TECHNOLOGIES SMM-770, Operating Manual

Search results

Summary of Contents for SMM-770

Reviews:

Related manuals for SMM-770

Brands by name

Popular brands