manualshive.com logo in svg

Trinamic TMCM-1311, Firmware Manual, Page: 77 / 109

Share
Download
Trinamic TMCM-1311 Firmware Manual Download Page 77

TMCM-1311 TMCL Firmware V1.11 Manual (Rev. 1.17 / 2015-NOV-05) 

77 

 

 
www.trinamic.com 

Number  Axis Parameter  Description 

Range  [Unit] 

Acc. 

209 

Encoder counter 

 

The value of an encoder register can be read 
out or written. 

[encoder steps] 

RW 

210 

Encoder 
resolution 

Resolution of the encoder in absolute 
positions. 
Quadrature encoder: 1 line = 4 positions  

0… 65535 
[positions] 

RW 

212 

Max. encoder 
deviation 

When the actual commanded position and the 
encoder position (parameter 209) differ more 
than defined by this parameter the motor will 
be stopped.  
This function is switched off when the 
maximum deviation is set to zero. 
If the value is negative and the maximum 
encoder  deviation  is  exceeded, the motor 
current will be switched off so that the axis can 
be turned freely. The new starting position will 
be detected. With the next command the motor 
can be driven as usual. 
This function is used in open loop mode and 
closed loop mode. 

−2.147.483.648… 

+2.147.483.647 
[µsteps] 
 

RWE 

214 

Power down 
delay 

Standstill period before the current is changed 
down to standby current. The standard value is 
200 (value equates 2000msec). 

1… 65535 
[10msec] 

RWE 

230 

Gamma 

Actual field weakening value (field weakening 
= speed dependent Back EMF compensation). 
The read-out value can be useful to choose 
values for axis parameters 108 and 109. 

0… 255 
Default = 255 
 
 

R 

233 

Virtual actual 
position 

With this parameter the actual virtual position 
of the ramp generator can be read out.  

−2.147.483.648… 

+2.147.483.647 
[µsteps] 

R 

236 

CL actual target 
current scale 
factor 

Actual target value of the current scale factor 
as defined by axis parameters 113, 114, 116, 
and 117. Due to the configurable delays using 
axis parameters 120 and 121, the actual target 
current scale factor may be different to the 
actual current scale factor. 

0… 255 
[1/256] 

R 

237 

Position error 

This parameter indicates the difference 
between the virtual actual position of the ramp 
generator and the measured position of the 
motor.  

−2.147.483.648… 

+2.147.483.647 
[µsteps] 
[encoder steps] 

R 

Summary of Contents for TMCM-1311














































































































Reviews:

No comments