manualshive.com logo in svg

TriContinent 8441 series, Operation And Maintenance Manual

Share
Download
TriContinent 8441 series Operation And Maintenance Manual Download Page 7

1.3

AC LINE VOLTAGE SELECTION

This instrument was supplied with a Fuse Module and two different types of spare fuses.   The 
Fuse Module is ready to be installed into the Power Entry Module located on the back of the 
instrument as shown in the following examples.   The Fuse Module must be installed into the 
Power Entry Module so that the proper voltage for your area is shown in the correct manner, 
as illustrated.   If you are not sure of the setting that is right for your area, contact your local 
power company.

1.3.1 120 LINE VOLTAGE SELECTION

The small arrow below the selected "110-120V" voltages shown on the Fuse Module must be 
aligned with the 

WHITE 

arrow on the Power Entry Module for proper OPERATION.

WARNING!  Disconnect power cord before continuing onto the next steps!

Multiwash III

!

ILLUSTRATION OF THE PROPER ORIENTATION OF THE FUSE MODULE
FOR OPERATION IN THE VOLTAGE RANGE OF 99 TO 132 VOLTS

STEP 1

STEP 2

STEP 3

2

Summary of Contents for 8441 series












































Reviews:

No comments

Brands by name

Popular brands

Load more brands