manualshive.com logo in svg

TriContinent 8441 series, Operation And Maintenance Manual

Share
Download
TriContinent 8441 series Operation And Maintenance Manual Download Page 38

SYMPTOM

PROBABLE CAUSE

REMEDY

11. Grinding noise from the back of 

the instrument and no fluid 
movement.

Syringe plunger is stuck due to 
dried wash buffer freezing the 
plunger to the syringe.

Turn the power Off and On and 
verify if syringe is working.

Turn the power Off. Take a large 
standard screw driver and turn the 
Stepper Motor Nut, counter 
clockwise 5 turns.
Turn the Power On.

The Syringe assembly needs to be 
replaced with replacement, Catalog 
# 938. Follow the directions 
supplied with the replacement kit.

Syringe plunger is out of follower.

See symptom #13.

12. Syringe plunger pops out of 

traveler nut.

Kink or blockage in tubing from 
Wash and Rinse reservoir, to the 
syringe valve.

Clear inlet tubing of all obstructions. 
Reset syringe plunger.

Wash and rinse reservoir inlet filter 
clogged.

Backflush or replace filters.

The syringe motor assembly needs 
to be replaced. Contact your 
distributor for assistance.
See Appendix 2.

13. “E02” displayed.

Syringe plunger has become 
disconnected, or jammed. See 
symptoms #11 and 12 for possible 
causes.

Turn off the instrument to reset it 
and see symptoms #11 and 12 for 
remedies.

14. Any ERROR code other than 

“E02”.

Damage to the instrument by 
electrical outage, brown out, low 
voltage, or high voltage spikes.

Turn off instrument to reset it and 
contact your distributor for 
assistance.
See Appendix 2.

5.2

TROUBLESHOOTING TABLE (CONTINUED)

Multiwash III

33

Summary of Contents for 8441 series












































Reviews:

No comments

Brands by name

Popular brands

Load more brands