background image

 

 

 

 

 13 

SPECIFICATIONS 

 

DIMENSIONS 
 
PETROSMART EZ Console 

 

 

 

8" W x 4-1/2" H x 9-3/4" D 

PETROSMART EZ Dispenser IC Box for 

 

10" W x 11-1/2" H x 4-3/4" D 

PETROSMART EZ DPT credit card module IC Box  

10" W x 11-1/2" H x 4-3/4" D 

 
WEIGHTS 
 
PETROSMART EZ Console 

 

 

7 lbs. 

PETROSMART EZ IC Box for BENNETT 

8 lbs. 

PETROSMART EZ Cable (25 ft)   

 

2 lbs. 

 

      NOTE: 

The above weights do not include shipping cartons or packing materials.

 

 
 

PERIPHERAL INTERFACE INSTALLATION 

 

In compliance with the UL regulations and standards that apply to the Petroleum Industry, the following 
information establishes installation parameters for the use of peripheral equipment with the PETROSMART EZ 
Control Console. 
 
1.  Any peripheral equipment must be UL listed. 
 
2.  Any peripheral equipment must have an Electronics Industry Association (EIA) Standard RS-232C or RS-      

             422A communications interface (whichever is appropriate for the application). 

 
3.  Any peripheral equipment must not be installed in or above a hazardous location. 
 
4.  The peripheral interconnection cable must be either UL Style 1061 or 2462 suitable for interconnection of  

             electronic equipment. 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for PETROSMART EZ
















Reviews: