background image

FAULT FINDING  

(Continued)

FAULT

POSSIBLE CAUSE

ACTION

FIRE OUT

Chimney blockage continued.

To start boiler, push the Safety Switch reset

button and re-light fire if necessary.

(See Fig 2.)

Note:

If a flue blockage is not found, the

Safety Switch may have operated as a 

result of persistent downdraught.  If this is 

the case, an anti-downdraught cowl should

be fitted to the top of the chimney such as 

an ‘OH’ pot or similar, or extend the chimney

height above the pressure zone.

FAILURE TO REACH

Continuous fan blowing

Check that system is not in excess of boiler

THERMOSTAT SETTING

output.

Blockage in hopper.

Empty hopper and remove obstruction.

Clinker and ash build up in fire box.

Declinker firebed and if necessary re-light

boiler.

Fan runner blades choked.

Remove and clean.

Air control flap not opening

Remove fan and clean flap to ensure free  

to “blast” setting.

operation.

BLOW BACK

Delayed ignition of flue gases.

Always recover fire to a bright condition as 

quickly as possible after clinkering.

Incorrect declinkering

Ensure fire is recovered by turning on fan

for a few minutes both before and after

declinkering.

Over declinkering

Do not declinker more than two strokes at 

any declinkering operation.

Hopper allowed to empty below fuel regulator

plate and then re-filled. Always keep hopper

topped up and never let fuel fall below fuel

regulator plate.

EXCESSIVE

No system controls.

Fit time-switch and room stat. to control

FUEL CONSUMPTION

heating pump for specific periods of the day.

Also fit thermostat radiator valves or zone

valves controlled by room stats..

Boiler thermostat sensing phial

Stop cause of draught and ensure stat. phial  

chilled by a cold draught causing

is thermally insulated by the fibre glass

stat, to keep fan running.

blanket inside boiler casing.

Firebed partly choked with ash

Declinker firebed several times until live fire

and clinker causing fan to blow

is seen at front of bed. Also remove any

continuously in an attempt to

large clinkers that may have built-up at 

reach stat. setting.

either side of fire-bed. Remember the more

fuel in combustion the quicker the fan is shut

off by the thermostat.

13

 

 

 

 

 

 

Summary of Contents for TRG 45



















Reviews: