background image

HEALTH AND SAFETY

INFORMATION FOR THE INSTALLER AND SERVICE ENGINEERS

Under the Consumer Protection Act 1987 and the Health and Safety at Work Act 1974, it is a

requirement to provide information on substances hazardous to health (COSHH Regulations

1988).

The Company takes every reasonable care to ensure that these products are designed and

constructed to meet these general safety requirements, when properly used and installed.

To fulfil this requirement products are comprehensively tested and examined before despatch.

This appliance may contain some of the items below.

When working on the appliance it is the Users/Engineers responsibility to ensure that any necessary

personal protective clothing or equipment is worn appropriate to parts that could be considered

as being hazardous to health and safety.

The installer should be aware of his responsibilities under the Act and provide, where necessary,

appropriate protection for persons carrying out the installation.

INSULATION AND SEALS

Glass Rope, Mineral Wool, Insulation Pads, Ceramic Fibre, Glass Insulation.

May be harmful if inhaled.  May be irritating to the skin, eyes, nose or throat.  When handling avoid

inhalation and contact with eyes.  Use (disposable) gloves, face masks and eye protection.

After handling wash hands and other exposed parts.  When disposing, reduce dust with water

spray, ensure parts are securely wrapped.

GLUES, SEALANTS & PAINT

Glues, Sealants and Paints are used in the product and present no known hazards when used in

the manner for which they are intended.

 

 

Summary of Contents for TRG 45



















Reviews: