TRI tool BEVEL MASTER 208B Operation Manual Download Page 37 | Manualshive

Page: 37 / 58

background image

35

Model 208B BEVELMASTER

®

92-1482 Rev. 190410

10. MAINTENANCE

Clean all components and coat them with a light film of oil after use.
Use a clean, non-detergent oil, preferably SAE 10 (90 SSU) or lighter or oil as

specified for the air motor.

Figure: 17. Areas That Need to be Cleaned

10.1

AIR SUPPLY

The Model 208B requires an adequate filter/regulator/lubricator (FRL) in the air

supply line. The motor warranty is void if damage occurs from contaminated air

or lack of lubrication.
When the Model 208B is operated in the vertical position, cutting head up,

turn it up side down and remove the chips and/or other debris after a bevel is

completed.
Tool life may be severely shortened, unless chips and/or other debris that

accumulate on the cutting head during the machining operation are removed.

«
...
35
36
37
38
39
...
»

Summary of Contents for BEVEL MASTER 208B



























































Reviews:

No comments

Related manuals for BEVEL MASTER 208B

Brand: OETIKER Pages: 30

Brand: Parkside Performance Pages: 134

Brand: Kärcher Pages: 208

Brand: Erbauer Pages: 78

Brand: Westfalia Pages: 34

Brand: Alemite Pages: 66

Brand: Greencut Pages: 20

Brand: Stanley Pages: 128

Brand: Parkside Pages: 19

Brand: 9circle Pages: 14

Airetool 2055-R Series

Brand: Apex Tool Group Pages: 12

Brand: WAGNER Pages: 56

Brand: BorMann Pages: 9

Brand: Baileigh Industrial Pages: 44

Brand: Gearwrench Pages: 4

Brand: Yost Vises Pages: 5

Brand: Greenlee Pages: 12

Brand: Rockwell Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands