manualshive.com logo in svg

Tri-Clover Tri-Flo CL Series, Service & Installation Manual

Share
Download
Tri-Clover Tri-Flo CL Series Service & Installation Manual Download Page 27

- 27 -

TROUBLESHOOTING

PROBLEM

PROBABLE CAUSE

REMEDY

5. Pump is noisy.

a. Bent impeller.

a. Remove cover and check

impeller against a known
straightedge.

b. Motor is rotating in the

b. Verify motor is wired

wrong direction.

according to manufacturer’s
instructions.

c. Impeller clearance is not

c. Remove casing and verify

within tolerance.

clearance between impeller
rear and casing is correct.

d. Pump cavitation.

d. See cavitation causes in

the INSTALLATION section
of these instructions.

e. Solid particles in pump.

e. Remove cover and check

for particles in the pump.

6. Fluid leaks at sealing

a. Worn seals or damaged

a. Disassemble pump

surfaces.

o-rings.

according to the
DISASSEMBLY sequence
in these instructions.
Replace all worn seals or
damaged o-rings.

b. Not enough compression

b. Disassemble pump

on rotating seal.

according to the
DISASSEMBLY sequence
in these instructions.
Replace spring.

Summary of Contents for Tri-Flo CL Series












































Reviews:

No comments

Brands by name

Popular brands

Load more brands