manualshive.com logo in svg

Tri-Clover Tri-Flo CL Series, Service & Installation Manual

Share
Download
Tri-Clover Tri-Flo CL Series Service & Installation Manual Download Page 17

- 17 -

MAINTENANCE

2.

Remove impeller.

3.

Remove casing (1) by removing nuts (13) and washers (14).

4.

Torque hex head screws (37) securing the compression ring and threaded compression ring to
132 lb-in or 11 lb-ft (15 Nm).  Note that hex head screws are metric (wrench size is 10mm).

ROTATING SEALS AND PUMP CASING ASSEMBLY

Type DG - External Balanced Seal

1.

If assembling DG type seals, install o-ring (5) into rotating seal (15).  Then assemble the rotating
seal (15) and spring (16) onto the drive collar (17).

For the CL4311 or CL6410 pump, insert the pin (19) into the drive collar, and install the o-ring
(5) into the rotating seal (15).  Then assemble the rotating seal (15) and spring (16) onto the
drive collar (18).

2.

Place the assembled seal on the stub shaft. The drive collar notch must align with the pin on the
stub shaft.

Ensure the drive collar pin enters the notch on the rotating seal cup when the spring is
compressed.

Drive Collar Pin

Notch in Cup

Torque 6 compression ring screws to 132 lb-in or 11 lb-ft
(15Nm).  Screws are metric.  Wrench size is 10mm.

Summary of Contents for Tri-Flo CL Series












































Reviews:

No comments

Brands by name

Popular brands

Load more brands