manualshive.com logo in svg

Traxxas Slayer Pro 4WD 5908, Owner'S Manual

Share
Download
Traxxas Slayer Pro 4WD 5908 Owner'S Manual Download Page 41

Slayer 

• 

41

There are two different rocker arm sets that are compatible with Slayer.  
Both sets will allow the wheel to travel a total of 60mm in the vertical 
direction.  From the ride height position, the wheel will be able to travel 
40mm in the upward direction (bump), and 20mm in the downward 
direction (droop).  The Slayer comes equipped with the Progressive 2 
rocker set, which offers a good balance of progressive rate for predictable 
body roll, brake dive, and high-speed stability.

The Progressive 3 rocker arm set (available separately) uses a higher 
progressive rate that will provide a firmer feel, reducing body roll, brake 
dive and rear squat.  Installation of the Progressive 3 rocker arm requires 
the following parts:
#5359 Progressive 3 Rocker Arm Set
#5133 Pushrod Spacers (these are required to lengthen the pushrods to 

maintain proper suspension travel.)

The chart below demonstrate the effect of the various rocker arms on 
wheel force as the suspension is compressed. On the progressive rate, 
wheel force is light at first and increases as the suspension is compressed.

Bump Steer Elimination Chart

The illustrations and the following table detail the position of the outer 
toe link end for various caster and roll center settings to eliminate bump 
steer. The shims and the hollow balls used to adjust bump steer are 
provided with your vehicle.

Rear

When the rear upper control 
arms are mounted in the lower 
of its two mounting holes in  
the bulkhead (roll center), the 
tall hollow ball should be used 
as shown.

Rocker Arm

Total Travel

Progressive Rate

Progressive 2

60mm

(40mm up / 20mm down)

Medium

Progressive 3

60mm

(40mm up / 20mm down)

High

Outer Toe Link End Setup

Caster

    5°    7.5°    10°    12.5°    15°

Control Arm 

Mounting Hole on 

Front Bulkhead

Upper

Lower

Upper

Lower

Upper

Lower

Upper

Lower

Upper

Standard 

Hollow Ball
Thin Shim
Thick Shim

Thin Shim
Standard

Hollow Ball
Thick Shim

Tall Center 

Hollow Ball

Thick Shim
Standard

Hollow Ball
Thin Shim

Thick Shim
Thin Shim
Standard

Hollow Ball

FRonT

Control Arm 

Mounting Hole on 

Rear Bulkhead

Outer Toe Link 

End Setup

Upper

Lower

Tall Center 

Hollow Ball 

(stock)

Tall Upper 

Hollow Ball

Constant Rate Travel

Wheel Travel

Wheel Force

0

2

4

6

8

10

12

14

16

18

20

10

20

30

40

50

60

70

80

90

Progressive Rate Travel

Advanced Tuning Adjustments

Summary of Contents for Slayer Pro 4WD 5908













































Reviews:

No comments

Brands by name

Popular brands

Load more brands