background image

 Slayer

This model is not intended 
for use by children (minors) 
under 16 years of age 
without the supervision 
of a responsible and 
knowledgeable adult.

All instructions and 
precautions outlined in this 
manual should be strictly 
followed to ensure safe 
operation of your model.

Safety Precautions

Models require detailed 
setup, and/or maintenance 
procedures with required 
support equipment. 
Previous experience with 
radio controlled models 
is mandatory. These 
models are capable of very 
high speeds and require 
an even higher level of 
skilled driving control.

H`^aaAZkZa2Bng^VYHZb^7daY

1 2 3 3+ 4 5

bluehighway font

For Expert Drivers

Choose the Model That is Right For You.

For individual Models

No previous experience with radio controlled models is required.

Models require a minimum of setup, maintenance, or support equipment. 

Previous experience with radio controlled models is mandatory. These 

models are capable of high speeds, requiring experienced driving control. 

Models require detailed setup, and/or maintenance procedures with required 

support equipment. 
Previous experience with radio controlled models is mandatory. 

These models are capable of very high speeds and require an even higher 

level of skilled driving control. Models require detailed setup, and/or mainte-

nance procedures with required support equipment. 

For Expert Drivers Only.

 This product is capable of extreme speed 

and acceleration! It carries our highest skill level rating and is intended 

for expert drivers only. Experience with nitro-powered radio controlled 

models is required!

Previous experience with radio controlled models is recommended.

Models require a higher level of setup, maintenance, or support equipment. 

No previous experience with radio controlled models is required.

Model requires a minimum of setup, maintenance, or support equipment. 

Previous experience with radio controlled models is mandatory. This model is 

capable of high speeds, requiring experienced driving control. Model requires 

detailed setup, and/or maintenance procedures with required support 

equipment. 

Previous experience with radio controlled models is mandatory. This model is 

capable of very high speeds and requires an even higher level of skilled driving 

control. Model requires detailed setup, and/or maintenance procedures with 

required support equipment. 

For Expert Drivers Only.

 This product is capable of extreme speed 

and acceleration! It carries our highest skill level rating and is intended 

for expert drivers only. Experience with nitro-powered radio controlled 

models is required!

 Previous experience with radio controlled models is recommended.

Model requires a higher level of setup, maintenance, or support equipment.

BELOW TEXT HAS BEEN UPDATED on 3-14-07
Kent wants maintenance text to be at the END of the paragraph.-- KB

All of us at Traxxas want you to safely enjoy your new Slayer. Operate 
your Slayer sensibly and with care, and it will be exciting, safe, and fun 
for you and those around you. Failure to operate your Slayer in a safe 
and responsible manner may result in property damage and serious 
injury. The precautions outlined in this manual should be strictly 
followed to help ensure safe operation. You alone must see that the 
instructions are followed and the precautions are adhered to. 

IMPoRTAnT PoInTS To REMEMBER

  Slayer is very fast! The Slayer is intended for experienced users with 

a high level of skill. The TRX 3.3 Racing Engine is extremely powerful 
and may require skilled driving to maintain control. Children under 
16 years of age and inexperienced drivers should not operate the 
Slayer without the supervision of a responsible and knowledgeable 
(experienced) adult.

 

Model engine fuel is dangerous and highly poisonous.

  

Always follow all directions and precautions printed on the fuel 
container. Model engine fuel is poisonous to humans and animals. 
Drinking the fuel can cause blindness and death. Handle with care 
and respect.

  Model engine fuel, especially when in a fuel dispensing bottle, may 

look like a cool drink to a child. 

Keep all fuel out of the reach of 

children at all times. Do not place fuel containers on the ground 
where children can reach them while you are driving.

  Model engine fuel is flammable. Never allow smoking, sparks,  

heat or flame in the presence of fuel or fuel vapors.

  

  The engine, brakes, and exhaust system may become extremely 

hot during use. Be careful not to touch the parts, especially when 
refueling or stopping the engine.

  Prolonged exposure to the engine exhaust can be harmful. Avoid 

breathing the engine exhaust. Always run your Slayer outdoors,  
in a well-ventilated area. Never run the engine indoors. 

  Do not operate your Slayer at night, or anytime your line of sight to 

the model may be obstructed or impaired in any way.

  Never operate your Slayer in crowds of people or busy pedestrian 

areas. Slayer is very fast  and could cause injury to those unaware of 
its presence. Keep small children at a safe distance away from the 
operating area.

  Because Slayer is controlled by radio, it is subject to radio 

interference from many sources beyond your control. Since radio 
interference can cause momentary loss of control, always allow 
a safety margin in all directions around your model to prevent 
collisions. 

  The engine can be loud. If the noise makes you uncomfortable, 

wear ear protection. Be considerate of your neighbors by not 
running your model early in the morning or late in the evening.

 

Most importantly, use good common sense at all times.

Summary of Contents for Slayer Pro 4WD 5908













































Reviews: