background image

4 • 1/16 SLASH 4WD

This model is not intended 
for use by children under 
14 years of age without the 
supervision of a responsible 
and knowledgeable adult.

All instructions and 
precautions outlined in this 
manual should be strictly 
followed to ensure safe 
operation of your model.

No previous experience with radio 
controlled models is required. 
Models require a minimum of setup, 
maintenance, or support equipment. 

control. Removing the battery connectors on the speed control or using 
the same-gender connectors on the speed control will void the product’s 
warranty.

• 

No Schottky Diodes

: External Schottky diodes are not compatible with 

reversing speed controls. Using a Schottky diode will damage the electronic 
speed control (ESC) and void the 30-day warranty.

• 

Using Two Batteries

: When using two batteries, the batteries must be 

connected in parallel. Never connect two batteries in series, this will cause the 
ESC to fail. See page 12 for more information.

Batteries and Battery Charging

Your model uses rechargeable batteries that must be handled with care for 
safety and long battery life. Make sure to read and follow all instructions and 
precautions that were provided with the battery packs and your charger. It is 
your responsibility to charge and care for the battery packs properly. In addition 
to your battery and charger instructions, here are some more tips to keep in 
mind.
•  Use the supplied charger to charge the included battery.  

See “Charging the Battery Pack” on page 11. 

•  Never leave batteries to charge unattended.
•  Remove the battery from the model while charging.
•  Always unplug the battery from the electronic speed control when the model 

is not in use and when it is being stored or transported.

•  Allow the battery pack to cool off between runs (before charging).
•  Do not use battery packs that have been damaged in any way.
•  Do not use battery packs that have damaged wiring, exposed wiring, or a 

damaged connector. 

•  Children should have responsible adult supervision when charging and 

handling batteries.

•   Do not charge batteries inside of an automobile. Do not charge batteries 

while driving in an automobile. The charger is equipped with a long cord 
intended to allow the battery to be charged outside of an automobile when 
using the automobile’s auxiliary power socket. If the cord will not reach 
outside of the automobile, find another power source.

•   Never charge batteries on wood, cloth, carpet or on any other flammable 

material.

•   Do not operate the charger in a cluttered space, or place objects on top of the 

charger or battery.

•   If a battery gets hot to the touch during the charging process (temperature 

greater than 140°F / 60°C), disconnect the battery from the charger and 
discontinue charging immediately.

•   Always store battery packs safely out of the reach of children and pets.
•   Do not short-circuit the battery pack. This may cause burns and severe 

damage to the battery pack and create the risk of fire.

•   Do not burn or puncture the batteries. Toxic materials could be released. If eye 

or skin contact occurs, flush with water.

•   Do not expose the charger to water or moisture.
•   Do not disassemble the charger.
•   Store the battery pack in a dry location, away from heat sources and direct 

sunlight.

•   Nickel-Metal Hydride (NiMH) batteries must be recycled or disposed of 

properly.

LiPo Batteries

Lithium Polymer (LiPo) batteries are becoming popular for use in R/C models 

due to their compact size, high energy density, and high-current output; 
however, these types of batteries require special care and handling procedures 
for long life and safe operation. 

Warning: LiPo batteries are intended only for 

advanced users that are educated on the risks associated with LiPo battery 
use. Traxxas does not recommend that anyone under the age of 14 use or 
handle LiPo battery packs without the supervision of a knowledgeable and 
responsible adult.

The XL-2.5 speed control is able to use LiPo batteries with nominal voltage not 

to exceed 7.4 volts (2S packs). LiPo batteries have a minimum safe discharge 
voltage threshold that should not be exceeded. The XL-2.5 is equipped with 
built-in Low-Voltage Detection that alerts the driver when LiPo batteries 
have reached their minimum voltage (discharge) threshold. 

It is the driver’s 

responsibility to stop immediately to prevent the battery pack from being 
discharged below its safe minimum threshold.

Low-Voltage Detection on the speed control is just one part of a comprehensive 

plan for safe LiPo battery use. 

It is critical for you, the user, to follow all 

other instructions supplied by the battery manufacturer and the charger 
manufacturer for proper charging, use, and storage of LiPo batteries. Make 
sure you understand how to use your LiPo batteries. 

Be aware that Traxxas 

shall not be liable for any special, indirect, incidental, or consequential damages 
arising out of the installation and/or use of LiPo batteries in Traxxas products. 

DO NOT ATTEMPT TO CHARGE LIPO BATTERIES OR ANY OTHER TYPE OF 

BATTERY WITH THE INCLUDED TRAXXAS CHARGER.

If you have questions about LiPo battery usage, please consult with your local 

hobby dealer or contact the battery manufacturer.

Recycling Your Traxxas Power Cell NiMH Battery

Traxxas strongly encourages you to recycle your Power Cell NiMH battery when it 
has reached the end of its useful life. 

Do not throw your battery in the trash.

 All 

Power Cell NiMH battery packs display the RBRC (Rechargeable Battery Recycling 
Corporation) icon, indicating they are recyclable. To find a recycling center near 
you, ask your local hobby dealer or visit www.call2recycle.org.

Skill Level = Myriad Semi Bold

1 2 3 3+ 4 5

bluehighway font

For Expert Drivers

Choose the Model That is Right For You.

For individual Models

No previous experience with radio controlled models is required.

Models require a minimum of setup, maintenance, or support equipment. 

Previous experience with radio controlled models is mandatory. These 

models are capable of high speeds, requiring experienced driving control. 

Models require detailed setup, and/or maintenance procedures with required 

support equipment. 
Previous experience with radio controlled models is mandatory. 

These models are capable of very high speeds and require an even higher 

level of skilled driving control. Models require detailed setup, and/or mainte-

nance procedures with required support equipment. 

For Expert Drivers Only.

 This product is capable of extreme speed 

and acceleration! It carries our highest skill level rating and is intended 

for expert drivers only. Experience with nitro-powered radio controlled 

models is required!

Previous experience with radio controlled models is recommended.

Models require a higher level of setup, maintenance, or support equipment. 

No previous experience with radio controlled models is required.

Model requires a minimum of setup, maintenance, or support equipment. 

Previous experience with radio controlled models is mandatory. This model is 

capable of high speeds, requiring experienced driving control. Model requires 

detailed setup, and/or maintenance procedures with required support 

equipment. 

Previous experience with radio controlled models is mandatory. This model is 

capable of very high speeds and requires an even higher level of skilled driving 

control. Model requires detailed setup, and/or maintenance procedures with 

required support equipment. 

For Expert Drivers Only.

 This product is capable of extreme speed 

and acceleration! It carries our highest skill level rating and is intended 

for expert drivers only. Experience with nitro-powered radio controlled 

models is required!

 Previous experience with radio controlled models is recommended.

Model requires a higher level of setup, maintenance, or support equipment.

BELOW TEXT HAS BEEN UPDATED on 3-14-07
Kent wants maintenance text to be at the END of the paragraph.-- KB

SAFETY PRECAUTIONS

Summary of Contents for 70054-1



























Reviews: