manualshive.com logo in svg

Travis Industries DVL EF II, Owner'S Manual

Share
Download
Travis Industries DVL EF II Owner'S Manual Download Page 16

16

 

Installation  (for authorized personnel only) 

© Travis Industries 

4040808

 

100-01201_000

 

Vent Connector Removal and Installation 

•

 

The vent connector is shipped attached to the insert, but may be removed to facilitate tight 
installations.  See the directions below for installation. 

1.  Route the flex vent through the chimney from above (leave an extra 914 mm at the top).  Make sure 

the flex is thoroughly stretched. 

2.  Remove the vent connector and attach it to the flex vent (see the instructions on the following page).  

NOTE: be careful of the anti-seize on the connector – it will stain clothing, etc. 

3.  Pull on the flex vent until the vent connector is at the same height as the insert.  Temporarily attach 

the flex vent to the top of the chimney (leave extra slack). 

4.  Slide the insert into place, guiding the vent connector into the guides on top of the insert. 

5.  Attach the vent connector to the appliance (see the following page for details). 

6.  Remove any excess slack in the flex line and attach the vent termination. 

4

3

2

1

5

6

2

 

Summary of Contents for DVL EF II











































Reviews:

No comments

Brands by name

Popular brands

Load more brands