manualshive.com logo in svg

Travis Industries DVL EF II, Owner'S Manual

Share
Download
Travis Industries DVL EF II Owner'S Manual Download Page 14

14

 

Installation  (for authorized personnel only) 

© Travis Industries 

4040808

 

100-01201_000

 

Altitude Considerations  

•

 

This heater has been tested at altitudes ranging from sea level to 2,400 m.  In this testing we have found that the 
heater, with its standard orifice, burns correctly with just an air shutter adjustment. 

•

 

Failure to adjust the air shutter properly may lead to improper combustion which can create a safety hazard. 
Consult your dealer or installer if you suspect an improperly adjusted air shutter. 

 

Vent Installation  

 

Inlet 76mm (3”)

Exhaust 102mm (4”)

Inlet

Exhaust

Termination Cap

(Simpson Part # 991)

168mm (6-5/8”) to 

76mm (3”) & 102mm 

(4”) Co-Linear Adapter 

(Travis Part # 

98900124)

76mm (3”) dia. Gas Liner

102mm (4”) dia. Gas Liner

Use hose-clamps 

to secure the vent.

Alternative Method: use high-temperature 

silicone and secure with screws.

Use hose-clamps to 

secure the vent.

Alternative Method: use 

high-temperature 

silicone and secure with 

screws.

 

 

 

 

Summary of Contents for DVL EF II











































Reviews:

No comments

Brands by name

Popular brands

Load more brands