manualshive.com logo in svg

Travis Industries DVL EF II, Owner'S Manual

Share
Download
Travis Industries DVL EF II Owner'S Manual Download Page 10

10

 

Installation  (for authorized personnel only) 

© Travis Industries 

4040808

 

100-01201_000

 

Clearances 

Due to the high temperature of the heater, it should be located out of traffic and away from furniture and 
draperies. 

Side 

Wall

Combustible or Non-Combustible Mantel

Combustible Top Facing

Non-Combustible 

Facing

Minimum Clearances

k

l

m

n

y

x

Sidewall to Insert
Side Facing
Top Facing*
Mantel*
Hearth Extension
Extension onto Hearth

255mm
102mm
900mm**
1000mm**
305mm
35mm

l

k

x

n

m

* The non-combustible top facing must extend 
25mm above the top of the surround panels.

** Measured from the base of the insert.

y

 

 

 

 

 

 

 

Mantel Clearances 

The maximum mantel depth is 305 mm at 1000 mm 
vertical height. 

** For mantel sizes over 305 mm, the vertical height 
must be raised to the equivalent length of the 
extended mantel depth as reference from the MIN 
value (305 mm). 

NOTE

:  The combustible area above the facing must 

not protrude more than 19 mm from the facing.  If it 
does, it is considered a mantel and must meet the 
mantel requirements listed in this manual. 

305 mm 

MIN 

430 mm 

1000 mm

MIN

1130 mm

1260 mm

Vertical Height

Mantel depth 

Summary of Contents for DVL EF II











































Reviews:

No comments

Brands by name

Popular brands

Load more brands