Transition Networks SISGM1040-244 User Manual Download Page 117

Page: 117 / 117

Transition Networks

SISGM1040-244

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

System Reboot interface

Troubles shooting

Verify that you are using the right power cord/adapter (DC 12 ~ 48V). Don’t use a power

adapter with DC output higher than 48V, or it may damage the switch.

Select the proper UTP cable to construct your network. Please check that you are using

the right cable. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cable for

RJ-45 connections: 100

Category 3, 4, or 5 cable for 10Mbps connections, 100

Category 5 cable for 100Mbps, or 100

Category 5e/above cable for 1000Mbps

connections. Also be sure that the length of any twisted-pair connection does not exceed

100 meters (328 feet).

Diagnosing LED Indicators:

the Switch can be easily monitored through panel

indicators, which describes common problems you may encounter and where you can

find possible solutions, to assist in identifying problems.

IF the power indicator does not light on when the power cord is plugged in, you may have

a problem with power cord. Then check for loose power connections, power losses or

surges at power outlet. IF you still cannot resolve the problem, contact your local dealer

for assistance.

If the Industrial Switch LED indicators are normal while the connected cables are correct,

but the packets still cannot transmit. Please check your system’s Ethernet devices’

configuration or status.

Summary of Contents for SISGM1040-244






















































































































Search results

Summary of Contents for SISGM1040-244

Reviews:

Related manuals for SISGM1040-244

Brands by name

Popular brands

Transition Networks SISGM1040-244, User Manual

Search results

Summary of Contents for SISGM1040-244

Reviews:

Related manuals for SISGM1040-244

Brands by name

Popular brands