Transition Networks SISGM1040-244 User Manual Download

Page: 48 / 117

Transition Networks

SISGM1040-244

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

spanning-tree

hello-time

[seconds]

Use the spanning-tree

hello-time global

configuration

command to specify

the interval between

hello bridge protocol

data units (BPDUs).

switch(config)#

spanning-tree

hello-time 3

spanning-tree

forward-time

[seconds]

Use the spanning-tree

forward-time global

configuration

command to set the

forwarding-time for the

specified

spanning-tree

instances. The

forwarding time

determines how long

each of the listening

and

learning states last
before the port begins
forwarding.

switch(config)#

spanning-tree

forward-time 20

stp-path-cost

[1~200000000]

Use the spanning-tree

cost interface

configuration

command to set the

path cost for Spanning

Tree

Protocol (STP)

calculations. In the

event of a loop,

spanning tree

considers the path

switch(config)#

interface

fastEthernet 2

switch(config-if)#

stp-path-cost 20

Summary of Contents for SISGM1040-244






















































































































Search results

Summary of Contents for SISGM1040-244

Reviews:

Related manuals for SISGM1040-244

Brands by name

Popular brands

Transition Networks SISGM1040-244, User Manual

Search results

Summary of Contents for SISGM1040-244

Reviews:

Related manuals for SISGM1040-244

Brands by name

Popular brands