Transition Networks SISGM1040-244 User Manual Download

Page: 42 / 117

Transition Networks

SISGM1040-244

24-Hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

or to 256000 kbps for

giga ports,

and zero means no

limit.

show bandwidth

Show interfaces

bandwidth control

switch(config)#

interface

fastEthernet 2

switch(config-if)#

show bandwidth

state

[Enable | Disable]

Use the state interface

configuration

command to specify

the state mode of

operation for Ethernet

ports. Use the disable

form of this command

to disable the port.

switch(config)#

interface

fastEthernet 2

switch(config-if)#

state Disable

show interface

configuration

show interface

configuration status

switch(config)#

interface

fastEthernet 2

switch(config-if)#

show interface

configuration

show interface status

show interface actual

status

switch(config)#

interface

fastEthernet 2

switch(config-if)#

show interface status

show interface

accounting

show interface statistic

counter

switch(config)#

interface

fastEthernet 2

switch(config-if)#

show interface

accounting

no accounting

Clear interface

accounting information

switch(config)#

interface

fastEthernet 2

switch(config-if)#

no accounting

Summary of Contents for SISGM1040-244






















































































































Search results

Summary of Contents for SISGM1040-244

Reviews:

Related manuals for SISGM1040-244

Brands by name

Popular brands

Transition Networks SISGM1040-244, User Manual

Search results

Summary of Contents for SISGM1040-244

Reviews:

Related manuals for SISGM1040-244

Brands by name

Popular brands