background image

Installation

14

 CVRF-SVN005C-EN

Motor Temperature Devices

The new Symbio™ panel comes with the motor winding 
temperature input LLID (IA26). This is used for motors that 
have RTD-type sensors embedded in the motor windings. If 
the motor does not have RTD-type sensors, motor 
temperature protection can be accomplished a temperature 
sensor which installed in the bulb well of the motor, and 
connect to the IPC bus.

Mount Display Arm and Display

1. Secure the arm to the control panel using the 5/16 - 18 x 

1-inch hex bolts, 5/16-inch lock washers, and 5/16 - 18 hex 
nuts provided. There are pre-drilled holes on the left and 
right sides of the control panel; select the side that’s most 
suitable for your specific application.

Note:

There is a production display arm bracket BRK04345 
provided that where applicable can be mounted to the 

existing control panel mounting arms. When used, the 
holes on the unused side should be plugged.

Figure 4.

Bolting display arm to the panel

2. Securely fasten the Tracer® AdaptiView™ display to the 

mounting plate on the end of the display arm with the 
hardware provided.

Figure 5.

Production display arm bracket

41B

1U2 J16-1

1X1-21

Vent line solenoid valve 
4L1

2X

1TB1-4

1X1-7

Vent line solenoid valve 
4L1 neutral

2TB1-9 (1TB1-8)

1X1-14

Oil pump interlock

2TB1-8 (1TB1-7)

1X1-15

Oil pump interlock

Table 6.

Field wiring cross reference, UCP2 to new 

panel (continued)

Existing 

Wire #

From

(in Existing Panel)

To

(in New 

Panel)

Description or 

Comments

Summary of Contents for Symbio CVRF

















































Reviews: