Trane IntelliPak SCRF 25, Installation, Operation And Maintenance Manual

Page: 79 / 120

SCXF-SVX01Q-EN 79
Pre-Startup
Before starting up units, perform the following
procedure to ensure proper unit operation.
Units with VFD
This panel is hinged to allow service access to fan
motor and belt drive components that are located
behind it.
N No otte e:: The panel weight rating is 225 lbs. total including
factory-installed components.
W WA AR RN NIIN NG G
P Prro op pe err F Fiie elld d W Wiirriin ng g a an nd d G Grro ou un nd diin ng g
R Re eq qu uiirre ed d!!
F Fa aiillu urre e tto o ffo ollllo ow w cco od de e cco ou ulld d rre essu ulltt iin n d de ea atth h o orr
sse erriio ou uss iin njju urry y..
A Allll ffiie elld d w wiirriin ng g M MU US ST T b be e p pe errffo orrm me ed d b by y q qu ua alliiffiie ed d
p pe errsso on nn ne ell.. IIm mp prro op pe errlly y iin nsstta alllle ed d a an nd d g grro ou un nd de ed d
ffiie elld d w wiirriin ng g p po osse ess F FIIR RE E a an nd d E EL LE EC CT TR RO OC CU UT TIIO ON N
h ha azza arrd dss.. T To o a av vo oiid d tth he esse e h ha azza arrd dss,, y yo ou u M MU US ST T ffo ollllo ow w
rre eq qu uiirre em me en nttss ffo orr ffiie elld d w wiirriin ng g iin nsstta alllla attiio on n a an nd d
g grro ou un nd diin ng g a ass d de essccrriib be ed d iin n N NE EC C a an nd d y yo ou urr llo occa all//
sstta atte e//n na attiio on na all e elle eccttrriicca all cco od de ess..
W WA AR RN NIIN NG G
H Ha azza arrd do ou uss V Vo olltta ag ge e w w//C Ca ap pa acciitto orrss!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on nss b be ello ow w cco ou ulld d rre essu ulltt iin n
d de ea atth h o orr sse erriio ou uss iin njju urry y..
D Diisscco on nn ne ecctt a allll e elle eccttrriicc p po ow we err,, iin nccllu ud diin ng g rre em mo otte e
d diisscco on nn ne eccttss a an nd d w wa aiitt ffo orr D DC C cca ap pa acciitto orrss tto o
d diisscch ha arrg ge e b be effo orre e sse errv viicciin ng g.. R Re effe err tto o tth he e
m ma an nu uffa accttu urre err’’ss rre ecco om mm me en nd da attiio on nss ffo orr p prro op pe err
d diisscch ha arrg ge e ttiim me e a ass D DC C b bu uss cca ap pa acciitto orrss rre etta aiin n
h ha azza arrd do ou uss v vo olltta ag ge ess a afftte err iin np pu utt p po ow we err h ha ass b be ee en n
d diisscco on nn ne ecctte ed d.. F Fo ollllo ow w p prro op pe err llo occkko ou utt// tta ag go ou utt
p prro occe ed du urre ess tto o e en nssu urre e tth he e p po ow we err cca an nn no ott b be e
iin na ad dv ve errtte en nttlly y e en ne errg giizze ed d.. V Ve erriiffy y w wiitth h a a C CA AT T IIIIII o orr IIV V
v vo ollttm me ette err rra atte ed d p pe err N NF FP PA A 7 70 0E E tth ha att a allll cca ap pa acciitto orrss
h ha av ve e d diisscch ha arrg ge ed d b be effo orre e tto ou ucch hiin ng g a an ny y iin ntte errn na all
cco om mp po on ne en nttss..
F Fo orr a ad dd diittiio on na all iin nffo orrm ma attiio on n rre eg ga arrd diin ng g tth he e ssa affe e
d diisscch ha arrg ge e o off cca ap pa acciitto orrss,, sse ee e P PR RO OD D--S SV VB B0 06 6* *--E EN N..
1. Remove the unit center cover panel to the left of the
VFD panel.
2. Verify/remove/discard the sheet metal shipping
screws along the top and bottom edges of the VFD
panel.
3. Disconnect the communications cable from the
keypad on the VFD door panel.
4. Turn the two slotted-head fasteners on the right
edge of the VFD panel fully counterclockwise.
5. Pull on the handle to swing the panel 180°.
N No otte e:: To secure the panel in the open position during
service procedures, attach the chain mounted to
the cabinet frame behind the unit center cover
panel to the chain retainer notch on the edge of
the VFD panel.
To close and reattach the panel, reverse the above
procedures.
N No otte e:: Verify that all wires are in proper position and
not rubbing once the panel has been secured.
Pre-Startup Checklist
Complete this checklist after installing unit to verify all
recommended installation procedures are complete
before startup. This does not replace the detailed
instructions in the appropriate sections of this manual.
Always read the entire section carefully to become
familiar with the procedures.
Supply Fan
• Verify the fan and motor shafts are parallel.
• Verify the fan and motor sheaves are aligned.
• Check the fan belt condition and tension. Adjust the
tension if belts are floppy or squeal continually.
Replace worn or fraying belts in matched sets.
• Ensure the fan rotates freely.
• Tighten locking screws, bearing set screws and
sheaves.
• Ensure bearing locking collars do not wobble when
rotated.
• Remove fan assembly tie down bolts.
• Ensure fan rotation is in direction of arrow on fan
housing. If incorrect, verify incoming power
phasing is correct. Switch wires on the fan contact
to properly phase fan if necessary.
Ductwork
• Ensure trunk ductwork to VAV boxes is complete
and secure to prevent leaks.
• Verify that all ductwork conforms to NFPA 90A or
90B and all applicable local codes
Water-Cooled Unit Piping
• Verify condensate drain, water piping drain plugs,
economizer header, and condenser vent plug are
installed.
Air-Cooled Units Only
• Verify leak test was performed after refrigerant
piping was installed.