Trane BMUC600AAA0100011 Installation, Operation And Maintenance Manual Download Page 40

Page: 40 / 84

BAS-SVX45F-GB

Tracer UC600 Operation

Connection Problems

Problem: Tracer UC600 is not responding, communicating, or is unable to connect with Tracer SC
or the Tracer TU service tool. (For more information about the Tracer TU service tool, see

“Configuring Tracer UC600 with Tracer TU,” p. 41

Possible cause: Defective application code in the controller.

Possible solution: Reload the application firmware.

Power down the controller (make sure to disconnect the USB cable).

2. Continuously hold down the service button pin while applying power. Press the service button

until the power LED illuminates green. Connect with Tracer TU and reload the application
firmware.

Note:

During the above process, the service LED will be green and the communication status LEDs
will be inactive.

Summary of Contents for BMUC600AAA0100011





















































































Search results

Summary of Contents for BMUC600AAA0100011

Reviews:

Related manuals for BMUC600AAA0100011

Brands by name

Popular brands

Trane BMUC600AAA0100011, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for BMUC600AAA0100011

Reviews:

Related manuals for BMUC600AAA0100011

Brands by name

Popular brands