Selecting the mounting position to install the indoor units
Select suitable places where the outlet air can be sent to the entire room, and
convenient to lay out the connection pipe, connection wire and the drainage
pipe to outdoor .
The ceiling structure must be strong enough to support the unit weight .
The connecting pipe, drain pipe and connection wire shall be able to go
though the building wall to connect between the indoor and outdoor units .
The connecting pipe between the indoor and outdoor units as well as the drain
pipe shall be as short as possible.
lf it is necessary to adjust the filling amount of the refrigerant, please refer to
the installation manual attached with the outdoor unit .
The connecting flange should be provided by the user himself .
The indoor unit has two water outlets one of which is obstructed at the factory (with a rubber cap) . Only the
outlet not obstructed (liquid inlet and outlet side) will be generally used during installation . lf applicable, both
the outlets should be used together .
An access port must be provided during installation of indoor unit for maintenance .
Select places for installation satisfying following conditions and at the same time obtain
the consent on the part of your client user.
Places where chilled or heated air circulates freely . When the installation height exceeds 3m warmed air stays
close to the ceiling . In such cases, suggest your client users to install air circulators .
Places where perfect drainage can be prepared and sufficient drainage .
Places free from air disturbances to the suction port and blowout hole of the indoor unit, places where the fire
alarm may not malfunction or short-circuit .
Places with the environmental dew-point temperature is lower than 28 C and the relative humidity is less than 80
% . (When installing at a place under a high humidity environment, pay sufficient attention to the prevention of
dewing such as thermal insulation of the unit . )
Ceiling height shall have the following height.
Summary of Contents for 4TXK6512G1000AA
