TracVision R4SL Installation Manual Download

Page: 21 / 23

If you need to connect three or more receivers,
install an Eagle Aspen multiswitch (KVH
Part #72-0310) between the grounding block and
the receivers, as shown in Figure A-1.

NOTE:

If you need to connect more than four

receivers, contact KVH Technical Support for
additional wiring instructions.

The use of a multiswitch interrupts

communications between the receiver and

antenna. As a result, you will need to install one

of the following for satellite switching:

DIRECTV

Automatic Switching (Ku-band HD Only):

To switch automatically between your selected

satellites using a DIRECTV H21-200 or H20-600

receiver, you will need to install the KVH HDTV

Tri-Sat AutoSwitch Kit (KVH Part #72-0301-03).

You can also equip multiple H21-200 and

H20-600 receivers with the Tri-Sat AutoSwitch,

allowing you to control satellite selection using

multiple receivers.

Manual Switching (Non-HD Only):

manually switch between your selected satellites,

you will need the TV/SAT Switch (KVH

Part #01-0245). When the TV/SAT Switch is

installed, you can switch between your selected

satellites at the press of a single button.

DISH 500 or ExpressVu

To manually switch between your selected

satellites, you will need the TV/SAT Switch

(KVH Part #01-0245). When the TV/SAT Switch

is installed, you can use a single button to switch

between your selected satellites.

DISH 1000 configurations must not exceed
two receivers.

IMPORTANT!

Figure A-1 Wiring 3 or 4 Receivers

Receiver #3

SATELLITE IN

OUT TO TV

TV ANT/CABLE IN

AUDIO

VIDEO

S-VIDEO

PHONE JACK

ATELLITE

Receiver #2

SATELLITE IN

OUT TO TV

TV ANT/CABLE IN

AUDIO

VIDEO

S-VIDEO

PHONE JACK

ATELLITE

Receiver #1

SATELLITE IN

OUT TO TV

TV ANT/CABLE IN

AUDIO

VIDEO

S-VIDEO

PHONE JACK

ATELLITE

Receiver #4

SATELLITE IN

OUT TO TV

TV ANT/CABLE IN

AUDIO

VIDEO

S-VIDEO

PHONE JACK

ATELLITE

RF2

RF1

Grounding

Block

Vehicle

AC Ground

Ground Wire

AC Power Input
100-240 VAC
50-60 Hz

Multiswitch

Note:

Although the label

shows “20V,” the unit
accepts a 24 VDC input.

13V

Rx4

ANT

Rx3

20V

Rx2

Rx1

18V

24 VDC
Power

upply

Antenna

Connecting 3 or More Receivers

Summary of Contents for R4SL
























Search results

Summary of Contents for R4SL

Reviews:

Related manuals for R4SL

Brands by name

Popular brands

TracVision R4SL, Installation Manual

Search results

Summary of Contents for R4SL

Reviews:

Related manuals for R4SL

Brands by name

Popular brands