manualshive.com logo in svg

TPS 901-C, Manual, Page: 9 / 31

Share
Download
TPS 901-C Manual Download Page 9

Page 8

2. Operating Modes

Press the 

 key to select the desired operating mode. The sequence is shown

in the following table…

Conductivity plus Temperature Mode

 2.76mS   25.0

o

c

Conductivity data is shown on the left and Temperature data is shown on the
right.

Select this mode to calibrate Conductivity.

↓↓

 

TDS plus Temperature Mode

 2.00ppK  25.0

o

c

TDS data is shown on the left and Temperature data is shown on the right.

Select this mode to calibrate TDS.

↓↓

 

Temperature Mode

  25.0

o

c

Temperature data only is shown on the left.

Select this mode to calibrate Temperature.

↓↓

 

Back to Conductivity plus Temperature mode

The following modes are added when the optional RS232 port is fitted…

RS232 Send Rate

Send Rate 

↑↑

   0

↓↓

Sets the Data output rate, in seconds.

Press 

 or 

 to set this value from 0 to 9999 seconds.

↓↓

 

RS232 Baud Rate

Baud Rate

↑↑

19200

↓↓

Allows selection of the RS232 Baud Rate.

Press 

 or 

 to select 300, 9600 or 19200 baud.

↓↓

 

Back to Conductivity plus Temperature mode

Summary of Contents for 901-C
































Reviews:

No comments