manualshive.com logo in svg

TPS 901-C, Manual, Page: 15 / 31

Share
Download
TPS 901-C Manual Download Page 15

Page 14

4.3 Calibration Messages

1.

 

If a Zero calibration has been successfully performed, the 

901-C

 will display

the Zero of the sensor and then return to TDS mode. For example…

 

Zero OK, 0.1%

Zero OK, 0.1%

2.

 

If a Span calibration has been successfully performed, the 

901-C 

will

display the k factor of the sensor and then return to TDS mode. For
example…

 

Cal OK, k=1.00

Cal OK, k=1.00

 

Note that " 

∗∗

 " in the TDS reading has now been replaced by a decimal

point, due to the successful calibration.

3.

 

If a Span calibration has failed, the 

901-C

 will display the following

messages and then the failed k factor of the sensor before returning to TDS
mode. For example…

 

Calibrate Failed

Calibrate Failed

 

 

 

then:

 

 

 

STD=36.00ppK ?

STD=36.00ppK ?

 

then:

 

k=0.70, Fails

k=0.70, Fails

 

Note that a " 

∗∗

 " replaces the decimal point in the TDS reading to indicate

that TDS is not correctly calibrated.

 

Check that the sensor is immersed at least to the vent hole in the body, and
that the standard is correct before attempting calibration again.

Summary of Contents for 901-C
































Reviews:

No comments