manualshive.com logo in svg

TPS 901-C, Manual, Page: 12 / 31

Share
Download
TPS 901-C Manual Download Page 12

Page 11

3.3 Calibration Messages

1.

 

If a Zero calibration has been successfully performed, the 

901-C

 will display

the Zero of the sensor and then return to Conductivity mode. For example…

 

Zero OK, 0.1%

Zero OK, 0.1%

2.

 

If a Span calibration has been successfully performed, the 

901-C 

will

display the k factor of the sensor and then return to Conductivity mode. For
example…

 

Cal OK, k=1.00

Cal OK, k=1.00

 

Note that " 

∗∗

 " in the Conductivity reading has now been replaced by a

decimal point, due to the successful calibration.

3.

 

If a Span calibration has failed, the 

901-C

 will display the following

messages and then the failed k factor of the sensor before returning to
Conductivity mode. For example…

 

Calibrate Failed

Calibrate Failed

 

 

 

then:

 

 

 

STD=2760uS  ?

STD=2760uS  ?

 

then:

 

k=0.70, Fails

k=0.70, Fails

 

Note that a " 

∗∗

 " replaces the decimal point in the Conductivity reading to

indicate that Conductivity is not correctly calibrated.

 

Check that the sensor is immersed at least to the vent hole in the body, and
that the standard is correct before attempting calibration again.

Summary of Contents for 901-C
































Reviews:

No comments