TPI The Value Leader 716 Manual Download Page 38

Page: 38 / 39

Appendix B: ERROR CODES & TROUBLESHOOTING

Code

Displayed

Code Definition

Possible Causes

Corrective Action

Flow

Error

Pump not drawing sample at
correct flow rate.

Blockage / kink in flue probe
hose.

Dirty or blocked filter(s).

Worn pump.

Check and rectify. See
Appendix A.

Replace filter(s). See
Appendix A.

Call Technical Helpline on
01293 530196 opt. 1

Sensor

Error

Oxygen sensor failed to
initialize

Flue probe connected to 716
prior to power up.

716 did not purge completely
from last sample.

Worn or defective oxygen
sensor.

Disconnect probe and
restart.

Purge for 20 minutes and
restart.

Call Technical Helpline on
01293 530196 opt. 1

Sensor

Error

Carbon monoxide sensor
failed to initialize.

Flue probe connected to 716
prior to power up.

716 did not purge completely
from last sample.

Worn or defective carbon
monoxide sensor.

Disconnect probe and
restart.

Purge for 20 minutes and
restart.

Call Technical Helpline on
01293 530196 opt. 1

bat

Low battery.

Battery needs to be charged. Charge battery. If the battery

won’t hold a charge, replace
the battery.

oFL

Overflow indication. The
pressure being measured is
outside the maximum
measurement capability.

Pressure being measured is
too high or low.

Pressure sensor damaged or
defective.

Remove pressure source.

Call Technical Helpline on
01293 530196 opt. 1

oFL

Overflow indication. The
temperature being measured
is outside the maximum
measurement capability.

Temperature being measured
is too high or low.

Remove pressure source.

oPEn

Unable to read thermocouple
(temperature).

Temperature probe not
connected to input.
Worn temperature sensor.

Connect temperature probe
to analyser.
Replace temperature probe
or flue probe.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for The Value Leader 716








































Search results

Summary of Contents for The Value Leader 716

Reviews:

Related manuals for The Value Leader 716

Brands by name

Popular brands

TPI The Value Leader 716, Manual

Search results

Summary of Contents for The Value Leader 716

Reviews:

Related manuals for The Value Leader 716

Brands by name

Popular brands