background image

 

38 

 

Chapter 5 Notice about the IrDA Infrared Interface 

 

When use the IrDA infrared interface the user must notice the following: 

1 The communication parameter must meet the following 

Baud rate: 9600bps 
Data bit: 8 
Parity: none 

Stop bit: 1 

2 Make sure the infrared windows of the host and printer aim each other, that 

is the View angle must within 30

°

 

3 Insure there is no  obstacle between the host and printer, and the distance 

must within 1 meter. 

4 If the clobber and lost data occurred, refer to the section 1,2,3 above 

5 If the printer doesn’t work when use the IrDA infrared interface, may sure 

the RS-232 communication cable has been plugged out. 

 

 

 

 

 

 

 

 

 

 

 

 

 

39 

 

Chapter 6 Notice about the Rechargeable Ni-MH Battery   

 

6.1 Ni-MH Rechargeable Battery characteristics 

6.1.1 Charging  characteristics 

The charging characteristic is affected by the current

temperature

time 

etc.  The current and the  temperature  affect  Ni-MH  rechargeable  battery 
charging characteristics obviously, temperature drop down or current increase 
may cause the charging voltage rise.   
   We recommend you charge the battery with the current within 1C 

1C

1500mA

, the temperature within 0

o

C~40

o

C. Charging the battery usually in 

the temperature exceed the range will  lower the capability of the battery. 
Overcharge  the battery from time to time may be underutilized  resulting 
insufficient use of the available capability. 
 
6.1.2 Discharging  characteristics 

The Ni-MH  rechargeable battery is  similar to  the Ni-Cd rechargeable 

battery. The discharge voltage is about 1.2 volt. The discharging characteristics 
is affected by the current

temperature etc. The higher discharge current and 

lower temperature the lower discharge voltage and efficiency. The maximum 
continuous discharge current is 3C. 
   
6.1.3 Cycle life characteristics 

Cycle Life of the battery is more than 500 times when it use  correctly. 

The battery is chemical, the capacity will be dropped down after use for many 
times also long time storage. Incorrect use may drop down the cycle life of the 
battery. 

 

6.1.4 Storage characteristics 

The storage characteristics include the self  discharge characteristic and 

long time storage characteristic. 

Self discharge indicates the phenomenon that the battery discharge in 

open circuit. The self discharge characteristic is affect by the environment.   

Research indicates that it is the best to store the battery with full charge 

status. The battery should be stored in the temperature about 10

30

o

C and the 

Summary of Contents for UP-PN24S


























Reviews: