background image

 

36 

 

Chapter 4 Battery Charge and Discharge  

 

4.1 Battery 

The printer uses a rechargeable battery with DC 6V 1500mAh. 

 

4.2 Charging Method 

Two charging methods are used for charging the battery: slow charging on 

the printer and external quick charging. 

1.Slow charging on printer 

Connect an external adaptor of DC12V/600mA to the DC jack of the 
printer, and the battery is installed on the printer. The charging time need 
12-16 hours. 

2.External quick charging 

Take out the battery from the printer and put it on the optional CX-101 
Quick Charger, connect the adaptor of DC12V/600mA to the Charger. 
The charging time need 4 hours. There are 4 indicators on the CX-101 
quick charger for indicating the status of the charging. More indicators 
light, more power charged. 
 

4.3 Discharging Method 

When the printer can’t work correctly due to the battery low, there may be 

some power in the battery. To reduce the remember effect of the battery and 
keep the capacity of the battery, strongly recommend charging after 
discharging sufficiently. 

1.Discharging on printer 

After power off, press and hold button ON more than 10 seconds until 
the both of red and green indicator light, the printer enters into 
discharging state and can’t do any operations. When the both of 
indicators are off, the discharging finished.   

2.External quick discharging 

CX-101quick charger has a quick discharging function. Put the battery on 
the charger, press the button located left and down corner. The battery 
enters quick discharging and then enters quick charging automatically 
after finished discharging. 

 

37 

 

4.4 Method of getting back the capacity 

If the battery discharged not entirely (the printer can work or the battery 

is discharged not sufficiently before charging) and charged not entirely (the 
charging time is not enough) more times, the battery capacity will reduce due 
to Ni-MH battery have some remembrance effect. To get back the capacity of 
the battery,  2 or 3 times of charging and discharging entirely are necessary. 
The method of discharging and charging the battery is same as descriptions of 
section 4.2 and 4.3.   

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for UP-PN24S


























Reviews: