manualshive.com logo in svg

Toyota 1ZZ-FTE, Installation Instructions Manual

Share
Download
Toyota 1ZZ-FTE Installation Instructions Manual Download Page 46

46

14. Installation engine compartment

1. INSTALL EXHAUST MANIFOLD GASKET.

(a) Place the new gasket onto the cylinder head studs.

K

: Gasket (9-2)

2. INSTALL EXHAUST MANIFOLD.

(a) Install the exhaust manifold onto the cylinder head 

using the 5 nuts.

K

: Nuts (5 pcs.) (9-3)

K

: Exhaust manifold (9-1)

Torque: 37 Nm

3. POSITION TURBO CHARGER.

(a) Position the Turbo charger underneath the exhaust 

manifold.

K

: Turbo charger (3-1)

(b) Position the gasket between the manifold and the 

Turbo charger.

K

: Gasket (3-7)

NOTICE: The embossed side of the gasket should 

face towards the exhaust manifold.

4. INSTALL TURBO CHARGER.

(a) Install the 4 bolts with the locking-plates (hand 

tighten).
NOTICE: The left front bolt is short (25 mm length).

K

: Bolt (3 pcs.) (4-1)

K

: Locking plate (2 pcs.) (4-3)

K

: Bolt (4-2)

K

K

K 5x

K

K

K 3x

K

1x

K 2x

Summary of Contents for 1ZZ-FTE

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands