manualshive.com logo in svg

Toyota 1ZZ-FTE, Installation Instructions Manual

Share
Download
Toyota 1ZZ-FTE Installation Instructions Manual Download Page 3

3

TABLE OF CONTENTS

TABLE OF CONTENTS  ............................................................................................................................................3

 PRECAUTIONS 

......................................................................................................................................................6

 PREPARATION 

......................................................................................................................................................7

1.  SST (Special Service Tools)  .......................................................................................................................7
2. Lubricants / Liquids ....................................................................................................................................7

  VEHICLE LIFT LOCATIONS ..................................................................................................................................8

 PARTS 

....................................................................................................................................................................9

1. Location .......................................................................................................................................................9

1.1. Turbo charger ......................................................................................................................................9
1.2. Heat shield.........................................................................................................................................10
1.3. Exhaust manifold ...............................................................................................................................11
1.4. Intercooler..........................................................................................................................................12
1.5. Air intake............................................................................................................................................13
1.6. Oil filter ..............................................................................................................................................14
1.7.  Oil pan and brackets..........................................................................................................................15
1.8. Electric components ..........................................................................................................................16
1.9. Cooling fan ........................................................................................................................................17
1.10. Templates........................................................................................................................................18
1.11.  Heat insulation, stickers and sparkplugs .........................................................................................19

2. Parts List ....................................................................................................................................................20
3. Specified torque ........................................................................................................................................24

 INSTALLATION 

PROCEDURES .........................................................................................................................26

1. Introduction ...............................................................................................................................................26

1.1. Si unit.................................................................................................................................................26
1.2.  Caution * notice * hint. .......................................................................................................................26
1.3.  Definition of symbols. ........................................................................................................................26
1.4.  Water hose and clamp.......................................................................................................................26
1.5.  Air hose and clamp............................................................................................................................27
1.6. Oil and coolant...................................................................................................................................27

2.  Parts to be removed (see workshop manual for detailed instructions) ...............................................28
3. Vehicle preparation ...................................................................................................................................30

1. Remove carbon canister. .....................................................................................................................30
2. Remove harness clamps. ....................................................................................................................30
3. Hole preparation. .................................................................................................................................31
4. Harness fixation. ..................................................................................................................................31
5. Harness grommet hole.(interior) ..........................................................................................................31

4.  Airfilter box heat shield preparation .......................................................................................................32

1.  Preparation heat shield. .......................................................................................................................32

5. Oil-sump preparation ................................................................................................................................33

1.  Install oil return adapter.  ......................................................................................................................33
2. Cleaning. .............................................................................................................................................33

6. Underbody protection preparation  ..........................................................................................................34

1. Undercover preparation. ......................................................................................................................34

7. Engine cover preparation .........................................................................................................................37

1. Engine cover preparation. ...................................................................................................................37

8. Cooling fan preparation ............................................................................................................................38

1. Install cooling-fan. ................................................................................................................................38
2.  Install bracket to cover. ........................................................................................................................38
3. Temperature sensor. ...........................................................................................................................38

9. Inlet pipe preparation ................................................................................................................................39

1.  Install vacuum hose adapter. ...............................................................................................................39
2. Preparation of VSV. .............................................................................................................................39
3. Install VSV. ..........................................................................................................................................39

Summary of Contents for 1ZZ-FTE

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands