manualshive.com logo in svg

Toyota 1ZZ-FTE, Installation Instructions Manual

Share
Download
Toyota 1ZZ-FTE Installation Instructions Manual Download Page 33

33

5.

Oil-sump preparation

1. INSTALL OIL RETURN ADAPTER.

(a) Mark the position of the oil return hose adapter.
(b) Punch-mark the drilling position.(spot-weld position)
(c) Pre-drill a 4 mm hole.
(d) Pre-drill to 6.5 mm
(e) Drill the hole out to 12mm.
(f) Remove burrs.

(g) Install the oil return adapter with the nut and copper 

gasket and Loctite No.270

K

: Adapter (14-1)

K

: Nut (14-2)

K

: Copper gasket (14-7)

Torque: 45 Nm

(h) Install the oil drain plug with a new gasket.

K

: Gasket (14-7)

R

: Oil drain plug

Torque: 37 Nm

2. CLEANING.

(a) Remove all liquid gasket remains from the contact 

surface.

(b) Clean the oil-sump in a parts wash system to ensure 

all gasket and drilling particles are removed.

NOTICE: Check if the gasket contact surface is 

straight and clear due to removal 
activities.

Ø 4 mm

Ø 6,5 mm

Ø 12 mm

K

K

K

K

R

Summary of Contents for 1ZZ-FTE

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands