Townlabs TL518 Instruction Manual Download Page 9 | Manualshive

Page: 9 / 24

background image

9

8.

Clean thoroughly ball screws. During machining protect the ball screws from the metal chip
particles. Keep them clean all the time.

9.

Wipe clean all the grease from the machine and oil all the moving parts.

Installation

The machine has four threaded holes on the bottom of the base. It is recommended to install leveling legs
or 3/8”-16 screws to level the machine on sturdy surface. Alternatively it is possible to bolt the machine
base to the table surface. This method is preferable if you will be machining heavy parts and the part
weight may tilt the machine when the X-carriage is in the extreme right or left position.
The location of the threaded inserts on the bottom of the base is shown on the picture below.

«
...
7
8
9
10
11
...
»

Summary of Contents for TL518

























Reviews:

No comments

Related manuals for TL518

Brand: FEDERAL PACIFIC Pages: 4

Brand: Xtool Pages: 16

STORMFORCE SFAR12

Brand: Draper Pages: 22

Brand: Whelen Engineering Company Pages: 4

Brand: Hilti Pages: 4

Brand: OMERA Pages: 50

Brand: Manhattan Pages: 16

Brand: Kolver Pages: 7

Brand: Varan Pages: 11

Brand: Jarvis Pages: 12

Brand: Bomag Pages: 58

Brand: P.I.T. Pages: 20

Brand: Olimpia splendid Pages: 148

Brand: Lumberjack Pages: 18

Brand: haubold Pages: 15

Brand: F.F. Group Pages: 52

Brand: Alemite Pages: 6

Brand: Sealey Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands